| Stop and start system does not operate
|
Stop and start system operation prohibition based on the battery conditions (Refer to "Stop and Start System does not Operate (Battery Condition)")
|
|
| Engine hood courtesy switch circuit
|
|
| Driver door courtesy switch circuit (system prohibits control)
|
|
| Driver door courtesy switch circuit (CAN communication DTC U014087)
|
|
| Driver door courtesy switch circuit
|
·
for 4 door:
·
for 5 door:
|
| Driver seat belt buckle switch circuit (system prohibits control)
|
|
| Driver seat belt buckle switch circuit (CAN communication DTC U014087)
|
|
| Front seat inner belt assembly
|
|
| Air conditioning system (system prohibits control)
|
|
Air conditioning system
(for Manual Air Conditioning System)
|
|
Air conditioning system
(for Manual Cooler System)
|
|
Air conditioning system
(for Heater System)
|
|
| Brake booster vacuum is low (system prohibits control)
|
|
| Brake booster vacuum is low
|
|
| Backup boost converter circuit
|
|
| Park/Neutral position switch assembly circuit (for Automatic Transmission)
|
|
| Neutral position switch circuit (for Manual Transmission)
|
|
| Starter signal circuit
|
|
| STA signal circuit
|
|
| Starter inrush current reduction relay circuit
|
|
| Crankshaft position sensor
|
|
| ECM
|
|
| Vacuum sensor assembly
|
|
| Stop and start system does not operate
|
Brake booster assembly
|
|
| Electromagnetic oil pump (for Automatic Transmission)
|
|
| Starter assembly
|
|
| The deceleration sensor zero point calibration is performed
|
|
| Airbag sensor assembly
|
|
| Skid control ECU (brake actuator assembly)
|
|
| CAN communication system
|
|
| Engine stop and start ECU
|
|
| Battery*1
|
|
| Wire harness or connector
|
-
|
| Starter assembly does not operate
|
Battery
|
|
| Starter assembly
|
|
| Park/Neutral position switch assembly (for Automatic Transmission)
|
|
| Neutral position switch (for Manual Transmission)
|
|
| Starter signal circuit (ECD system)
|
|
| Starter signal circuit
|
|
| Cranking speed decreases
|
Battery
|
|
| Starter inrush current reduction relay circuit
|
|
| Starter assembly
|
|
| Stop and start cancel indicator does not operate
|
Combination meter assembly
|
|
| Indicator circuit (CAN communication system)
|
|
| Engine stop and start ECU
|
|
| Stop and start indicator does not operate
|
Combination meter assembly
|
|
| Indicator circuit (CAN communication system)
|
|
| Engine stop and start ECU
|
|
| Stop and start control cannot be canceled
|
ECAN terminal voltage
|
|
| Stop and start cancel switch circuit
|
|
| Engine not stopped by stop and start control (stop and start operation prohibited)
|
Engine hood courtesy switch circuit
|
|
| Driver side door courtesy switch circuit
|
·
for 4 Door:
·
for 5 Door:
|
| Stop light switch assembly
|
|
| Clutch start switch assembly (for lower) (for Manual Transmission)
|
|
| Clutch switch assembly (for upper) (for Manual Transmission)
|
|
| Engine stop and start ECU
|
|
| The shift lever is operated without depressing the clutch pedal (system operation prohibition) (for Manual Transmission)
|
|
| Multi-information display screen does not change after pressing steering pad switch assembly
|
Stop and start priority control system
|
|
| Multi-information display screen changes without pressing steering pad switch assembly
|
Stop and start priority control system
|
|
| An interruption message is not displayed in the combination meter assembly when the stop and start system cancel switch (eco run cancel switch assembly) is pressing and holding
|
Stop and start priority control system
|
|
| The control mode changes but an interruption message is not displayed in the combination meter assembly
|
Stop and start priority control system
|
|
| The control mode does not change but an interruption message is displayed in the combination meter assembly
|
Stop and start priority control system
|
|
| Control mode returns to default mode after turning ignition switch ON
|
Stop and start priority control system
|
|