Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P200812  Intake Manifold Runner Control Bank 1 Circuit Short to Battery  P200814  Intake Manifold Runner Control Bank 1 Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P200873.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P200873

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P200812 Intake Manifold Runner Control Bank 1 Circuit Short to Battery Short in vacuum switching valve assembly (for swirl control valve) circuit for 3 seconds (2 trip detection logic).
·

Vacuum switching valve assembly (for swirl control valve)

·

Short in vacuum switching valve assembly (for swirl control valve) circuit

·

ECM


Comes on DTC stored SAE Code: P2010
P200814 Intake Manifold Runner Control Bank 1 Circuit Short to Ground or Open Open in vacuum switching valve assembly (for swirl control valve) circuit for 3 seconds (2 trip detection logic).
·

Vacuum switching valve assembly (for swirl control valve)

·

Open in vacuum switching valve assembly (for swirl control valve) circuit

·

ECM


Comes on DTC stored SAE Code: P2009

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P200812
P200814
2 seconds after engine is started, race engine for 1 second

WIRING DIAGRAM

A444434E01
4.177,0.542 4.74,0.771 0.563,0.229 10 false SCV- 2.646,0.396 2.802,0.594 0.156,0.198 10 false 2 2.896,0.542 3.458,0.771 0.563,0.229 10 false SCV+ 4.635,0.417 4.792,0.615 0.156,0.198 10 false 1 2.844,0.938 3.406,1.167 0.563,0.229 10 false E87 2.823,1.115 5,1.5 2.177,0.385 10 false Vacuum Switching Valve Assembly (for Swirl Control Valve) 3.625,3.01 4.854,3.208 1.229,0.198 10 false EFI MAIN 1.281,2.396 2.51,2.594 1.229,0.198 10 false EFI-MAIN 0.448,2.667 1.677,2.865 1.229,0.198 10 false FL MAIN 6.333,2.552 7.031,2.854 0.698,0.302 10 false MREL 5.99,2.656 6.688,2.958 0.698,0.302 10 false N2 6,2.448 6.698,2.75 0.698,0.302 10 false 14 6,0.531 6.698,0.833 0.698,0.302 10 false E5 5.99,0.354 6.688,0.656 0.698,0.302 10 false 10 6.313,0.521 7.01,0.823 0.698,0.302 10 false SCV 4.271,2.552 4.969,2.854 0.698,0.302 10 false 2 3.479,2.552 4.177,2.854 0.698,0.302 10 false 1 4.271,2.135 4.969,2.438 0.698,0.302 10 false 5 3.479,2.125 4.177,2.427 0.698,0.302 10 false 3 4.813,2.417 6.042,2.615 1.229,0.198 10 false EFI NO. 4 5.198,2.156 5.896,2.458 0.698,0.302 10 false 2 4.781,2.156 5.479,2.458 0.698,0.302 10 false 1 6.458,3.448 7.156,3.75 0.698,0.302 10 false ECM 1.74,2.146 2.438,2.448 0.698,0.302 10 false 2 1.313,2.146 2.01,2.448 0.698,0.302 10 false 1 0.594,3.375 1.667,3.573 1.073,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A067588C02
0.458,1.448 0.365,1.688 false 0.656,1.396 0.906,1.885 true 1.969,1.417 1.844,1.781 false 2.146,1.375 2.469,1.844 true 0.823,0.073 1.531,0.281 0.708,0.208 10 false VSV is ON 2.458,0.063 3.24,0.271 0.781,0.208 10 false VSV is OFF 0.781,0.427 1,0.625 0.219,0.198 10 false Air 2.521,1.76 3,1.958 0.479,0.198 10 false Port E 0.958,1.802 1.438,2 0.479,0.198 10 false Port E 1.906,1.708 2.375,1.906 0.469,0.198 10 false Port F 0.219,1.729 0.688,1.927 0.469,0.198 10 false Port F 2.229,0.438 2.448,0.635 0.219,0.198 10 false Air 2.76,0.583 3.333,0.781 0.573,0.198 10 false Air Filter

Connect the GTS to the DLC3.


b.

Disconnect the vacuum hoses from the vacuum switching valve assembly (for swirl control valve).


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 372 75

e.

Check the VSV operation when it is operated using the intelligent tester.

OK:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY FOR SWIRL CONTROL VALVE (RESISTANCE)
2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY FOR SWIRL CONTROL VALVE (RESISTANCE)
a.

Inspect the vacuum switching valve assembly (for swirl control valve).

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)

NG

10.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE)
3.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)
a.

Disconnect the vacuum switching valve assembly (for swirl control valve) connector.


b.
A249191C13
0.458,1.052 0.906,1.313 0.448,0.26 2.323,1.771 1.906,1.302 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.552,1.104 0.917,1.313 0.365,0.208 10 false E87 2.26,1.802 2.771,2.083 0.51,0.281 10 false SCV+
*a Front view of wire harness connector
(to Vacuum Switching Valve Assembly (for Swirl Control Valve))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E87-2 (SCV+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) - EFI MAIN RELAY)
4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) - ECM)
a.

Disconnect the vacuum switching valve assembly (for swirl control valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E87-1 (SCV-) - E5-10 (SCV) Always Below 1 Ω
E87-1 (SCV-) or E5-10 (SCV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) - EFI MAIN RELAY)
a.

Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the vacuum switching valve assembly (for swirl control valve) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN relay terminal 5 - E87-2 (SCV+) Always Below 1 Ω
EFI MAIN relay terminal 5 or E87-2 (SCV+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT ECM POWER SOURCE CIRCUIT

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.INSPECT ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Start the engine and wait for 2 seconds or more.


d.

Race the engine for 1 second or more.


e.

Enter the following menus: Powertrain / Engine / DTC.

Powertrain > Engine > Trouble Codes
50001 372

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE)
a.

Replace the vacuum switching valve assembly (for swirl control valve).

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED