The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the EGR valve removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
1.DRAIN ENGINE COOLANT
85110
2.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
55701J
3.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
26100G
4.REMOVE DIESEL THROTTLE BODY ASSEMBLY
87209
5.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Heater)
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
w/ Rear Heater:
Slide the 2 clamps and disconnect the 2 water hose sub-assemblies from the water pipe.
Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and No. 2 water by-pass pipe.
w/o Rear Heater:
Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and No. 2 water by-pass pipe.
16278
6.REMOVE NO. 2 WATER BY-PASS PIPE
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *A | w/ Heater |
| *B | w/o Heater |
for Laminated EGR Pre-cooler:
Detach the clamp, slide the clamp and disconnect the No. 18 water by-pass hose from the EGR pipe with cooler sub-assembly.
| *A | w/ Heater |
| *B | w/o Heater |
w/ Viscous Heater:
Slide the clamp and disconnect the water by-pass hose sub-assembly from the No. 2 water by-pass pipe.
w/ Heater:
Slide the clamp and disconnect the No. 13 water by-pass hose from the No. 2 water by-pass pipe.
Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.
Slide the clamp and disconnect the No. 16 water by-pass hose from the EGR pipe stay.
| *A | w/ Heater |
| *B | w/o Heater |
Remove the 3 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly.
89421C
7.REMOVE DIESEL TURBO PRESSURE SENSOR
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Disconnect the connector from the diesel turbo pressure sensor.
Disconnect the vacuum hose and remove the bolt and turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.
23265C
8.REMOVE GAS FILTER
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Disconnect the vacuum hose from the intake manifold.
Detach the clamp and remove the gas filter from the gas filter bracket.
12632
9.REMOVE NO. 2 ENGINE COVER BRACKET
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the 2 bolts and No. 2 engine cover bracket from the No. 3 water by-pass pipe sub-assembly and EGR valve adapter sub-assembly.
23941
10.DISCONNECT NO. 1 FUEL FILTER PROTECTOR
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Disconnect the connector from the fuel filter assembly.
Detach the clamp and disconnect the wire harness from the No. 1 fuel filter protector.
Remove the bolt and disconnect the No. 1 fuel filter protector from the body.
82121
11.DISCONNECT ENGINE WIRE
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Disconnect the 2 connectors from the turbocharger sub-assembly.
Detach the clamp and disconnect the connector from the intake mass air flow meter sub-assembly.
Disconnect the connector from the camshaft position sensor.
Detach the 3 clamps and disconnect the engine wire from the 2 wire harness clamp brackets.
Disconnect the 4 connectors from the 4 injector assemblies.
Disconnect the connector from the electric EGR control valve assembly.
Disconnect the connector from the glow plug connector.
Remove the bolt and disconnect the connector from the sensor wire of the common rail assembly.
Disconnect the 2 connectors from the vane pump assembly.
Detach the 2 clamps and disconnect the engine wire from the No. 3 water by-pass pipe sub-assembly and wire harness clamp bracket.
Detach the clamp, remove the bolt and disconnect the engine wire from the No. 4 water by-pass pipe sub-assembly.
25625
12.REMOVE EGR VALVE BRACKET
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.
25612
13.REMOVE NO. 2 EGR PIPE
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.
Remove the 2 gaskets.
25800
14.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Detach the clamp and disconnect the connector from the common rail assembly.
Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.
Remove the 2 bolts and electric EGR control valve assembly from the EGR valve adapter sub-assembly.
Remove the gasket.