Refer to DTC P008700.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P008700
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P107F62 | Fuel Rail Pressure Sensor "A"/"B" Signal Compare Failure | The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM |
Comes on | DTC stored | SAE Code: P107F |
| DTC No. | Data List |
|---|---|
| P107F62 | ·
Fuel Pressure (High) ·
Target Fuel Pressure (High) ·
Fuel Pressure (Low) / Fuel Pressure 2 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P107F62 | Idling for 1 second or more |
Refer to DTC P008700.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P008700
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Target Fuel Pressure (High), Fuel Pressure (High) and Fuel Pressure (Low) / Fuel Pressure 2.
| Tester Display |
|---|
| Target Fuel Pressure (High) |
| Fuel Pressure (High) |
| Fuel Pressure (Low) / Fuel Pressure 2 |
Start the engine.
Check the change in the values for the Data List items above when increasing the engine speed from idling to 3000 rpm with no load.
| Result | Proceed to |
|---|---|
| Fuel Pressure (High) or Fuel Pressure (Low) / Fuel Pressure 2 is always 10000 kPag or less
or Fuel Pressure (High) or Fuel Pressure (Low) / Fuel Pressure 2 is always 220000 kPag or higher |
A |
| Except above | B |
Normally, "Fuel Pressure (High)" is within 5000 kPag of "Target Fuel Pressure (High)".
A
B
Disconnect the fuel pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E105-5 (PR) - E7-18 (PCR1) | Always | Below 1 Ω |
| E105-2 (PR2) - E8-23 (PCR2) | Always | Below 1 Ω |
| E105-1 (VCS) - E8-22 (VCS) | Always | Below 1 Ω |
| E105-6 (VC) - E7-28 (VCM) | Always | Below 1 Ω |
| E105-4 (E2) - E7-19 (E2M) | Always | Below 1 Ω |
| E105-3 (E2S) - E8-21 (E2S) | Always | Below 1 Ω |
| E105-5 (PR) or E7-18 (PCR1) - Body ground and other terminals | Always | 10 kΩ or higher |
| E105-2 (PR2) or E8-23 (PCR2) - Body ground and other terminals | Always | 10 kΩ or higher |
| E105-1 (VCS) or E8-22 (VCS) - Body ground and other terminals | Always | 10 kΩ or higher |
| E105-6 (VC) or E7-28 (VCM) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P107F62 is output | A |
| No DTC is output | B |
A
B
Replace the common rail assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P107F62 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT