Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
51406A
1.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)
52618
2.REMOVE LOWER FRONT BUMPER ABSORBER
51405A
3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
4.DRAIN ENGINE COOLANT
53106B
5.REMOVE RADIATOR COVER SUB-ASSEMBLY
17751
6.REMOVE NO. 1 AIR CLEANER INLET
Remove the 2 bolts and No. 1 air cleaner inlet.
44360
7.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
Remove the 2 bolts.
Detach the clamps and disconnect the vane pump oil reservoir assembly.
17030
8.REMOVE AIR HOSE ASSEMBLY
16470
9.REMOVE RADIATOR RESERVE TANK ASSEMBLY
| *1 | No. 2 Water By-pass Hose |
Slide the clip and disconnect the No. 2 water by-pass hose from the radiator reserve tank assembly.
| *1 | No. 1 Water By-pass Hose |
|
Clip |
|
Bolt |
Slide the clip and disconnect the No. 1 water by-pass hose from the radiator assembly.
Remove the 2 bolts and radiator reserve tank assembly.
16571C
10.REMOVE NO. 1 RADIATOR HOSE
Slide the clips and remove the No. 1 radiator hose from the radiator assembly and water outlet sub-assembly.
88359
11.REMOVE VISCOUS HEATER V BELT (w/ Viscous Heater)
16711
12.REMOVE FAN SHROUD
| *1 | No. 2 Water By-pass Hose |
Slide the clip and disconnect the No. 2 water by-pass hose from the radiator assembly.
Loosen the 4 nuts holding the fan with fluid coupling assembly.
Remove the fan and generator V belt.
Detach the claws.
for Automatic Transmission:
Detach the clamp and disconnect the oil cooler inlet hose.
Remove the 4 nuts of the fan with fluid coupling assembly.
Detach the guides.
|
Remove in this Direction |
Remove the fan shroud together with the fluid coupling assembly as shown in the illustration.
Do not allow the radiator assembly to interfere with other parts.
Remove the fan pulley from the water pump assembly.
16572D
13.REMOVE NO. 2 RADIATOR HOSE
Slide the clips and remove the No. 2 radiator hose from the radiator assembly and water inlet.
14.REMOVE FRONT BUMPER
53510
15.REMOVE HOOD LOCK ASSEMBLY
17311B
16.REMOVE NO. 1 AIR INLET DUCT
Remove the clips.
Detach the claws, guides and remove the No. 1 air inlet duct.
86520
17.REMOVE LOW PITCHED HORN ASSEMBLY
Click hereVehicle Exterior>HORN>HORN>REMOVAL
86510
18.REMOVE HIGH PITCHED HORN ASSEMBLY (for 2-piece Type)
Click hereVehicle Exterior>HORN>HORN>REMOVAL
88590E
19.REMOVE BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)
for LH Side:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER FAN>REMOVAL
for RH Side:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER FAN>REMOVAL
53209B
20.REMOVE HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY
| *1 | Engine Room Main Wire |
Disconnect the connector.
Detach the clamps and disconnect the engine room main wire.
w/ Air Conditioning System:
| *1 | Air Conditioner Tube and Accessory Assembly |
Detach the clamp and disconnect the air conditioner tube and accessory assembly.
Remove the 2 bolts and hood lock support brace sub-assembly.
16546
21.REMOVE RADIATOR PROTECTOR (w/o Air Conditioning System)
Remove the 2 bolts.
Detach the guides and remove the radiator protector.
53205
22.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
| *1 | Engine Room Main Wire |
Remove the bolt and disconnect the engine room main wire.
for LHD:
| *1 | Engine Room Main Wire |
| *2 | Hood Lock Control Cable Assembly |
Remove the 4 bolts.
Detach the clamps and disconnect the engine room main wire and hood lock control cable assembly and remove the upper radiator support sub-assembly.
Do not allow the cooler condenser assembly to interfere with the radiator assembly. (w/ Air Conditioning System)
for RHD:
| *1 | Engine Room Main Wire |
| *2 | Hood Lock Control Cable Assembly |
Remove the 4 bolts.
Detach the clamps and disconnect the engine room main wire and hood lock control cable assembly and remove the upper radiator support sub-assembly.
Do not allow the cooler condenser assembly to interfere with the radiator assembly. (w/ Air Conditioning System)
32921D
23.DISCONNECT OIL COOLER INLET HOSE (for Automatic Transmission)
Slide the clip and disconnect the oil cooler inlet hose from the radiator assembly.
32922A
24.DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission)
Slide the clip and disconnect the oil cooler outlet hose from the radiator assembly.
16400
25.REMOVE RADIATOR ASSEMBLY
w/ Air Conditioning System:
|
Remove in this Direction |
Remove the radiator assembly from the vehicle as shown in the illustration.
Perform the following procedure with 2 or more people to prevent damage to the radiator assembly.
When removing the radiator assembly, do not damage the cooler condenser assembly.
Prepare a drain pan or cloth in case the coolant leaks.
w/o Air Conditioning System:
|
Remove in this Direction |
Remove the radiator assembly from the vehicle as shown in the illustration.
Perform the following procedure with 2 or more people to prevent damage to the radiator assembly.
Prepare a drain pan or cloth in case the coolant leaks.
16523A
26.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16535
27.REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.