The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the fuel lid lock control cable assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learming the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION (w/ Front Seat Side Airbag)
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)
for 7GR-FKS:
for 1GD-FTV:
Click hereGeneral>MAINTENANCE>1GD-FTV BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
73220
3.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH
for Semi-trim:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Semi-trim)>REMOVAL
for Full-trim:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Full-trim)>REMOVAL
62112
4.REMOVE COWL SIDE TRIM BOARD LH
55641
5.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER
77306
6.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the claw in the direction (1) indicated by the arrow shown in the illustration.
Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the fuel lid lock open lever sub-assembly.
Detach the clamp and remove the fuel lid lock open lever sub-assembly from the fuel lid lock control cable sub-assembly.
77035
7.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
Detach the clamp and disconnect the fuel lid lock control cable sub-assembly.
77310A
8.REMOVE FUEL TANK CAP ASSEMBLY
|
Remove in this Direction |
w/ Key Type:
Insert the mechanical key into the fuel tank cap assembly and turn the key in the direction of the arrow shown in the illustration to unlock the fuel tank cap assembly.
|
Remove in this Direction |
Remove the fuel tank cap assembly as shown in the illustration.
Detach the clamp and remove the fuel tank cap assembly.
w/ Urea SCR System:
Use the same procedure to remove the fuel inlet box ring.
77293A
9.REMOVE NO. 3 FUEL TANK FILLER PIPE SHIELD
|
Protective Tape |
Apply protective tape around the fuel filler opening lid assembly as shown in the illustration.
Remove the fuel inlet box ring as shown in the illustration.
| *1 | Fuel Inlet Box Ring | - | - |
w/ Urea SCR System:
Use the same procedure to remove the fuel inlet box ring.
While pushing the fuel tank filler pipe shield assembly into the vehicle, disconnect the fuel tank filler pipe shield assembly from the No. 3 fuel tank filler pipe shield as shown in the illustration.
w/ Urea SCR System:
Use the same procedure to disconnect the fuel tank filler pipe shield assembly.
Using a 4 mm hexagon socket wrench, remove the 7 screws.
|
Remove in this Direction |
Pull the No. 3 fuel tank filler pipe shield in the direction of the arrow shown in the illustration and remove it together with the fuel lid lock control cable sub-assembly.
Pull the fuel lid lock control cable sub-assembly out of the vehicle.
Detach the claw and remove the 7 grommets.
77035
10.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
Detach the clamp and remove the fuel lid lock control cable sub-assembly from the fuel filler opening lid lock sub-assembly.
77037
11.REMOVE FUEL FILLER OPENING LID LOCK SUB-ASSEMBLY
Perform this procedure only when replacement of the fuel filler opening lid lock sub-assembly is necessary.
Remove the nut and fuel filler opening lid lock sub-assembly.
77378A
12.REMOVE FUEL FILLER OPENING LID LOCK COVER
Perform this procedure only when replacement of the fuel filler opening lid lock cover is necessary.
Detach the clip and remove the fuel filler opening lid lock cover.