Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY (for Full-trim)
RM35X0E _58 Vehicle Interior _078602 SEAT BELT _0387529 FRONT SEAT OUTER BELT ASSEMBLY(for Full-trim) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for Full-trim)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION (w/ Pretensioner and Force Limiter)

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Pretensioner and Force Limiter)


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67912A 3.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67911B 4.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 67914B 5.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913B 6.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 8.REMOVE FRONT SEAT ASSEMBLY RH

a.

for Separate Seat Type:

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Separate Seat Type)>REMOVAL





Hide 74617A 9.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)

Hide 74680 10.REMOVE PILLAR ASSIST GRIP ASSEMBLY B (w/ Assist Grip)

Hide 73233 11.REMOVE OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for the other side.


a.
B541699C01
1.49,1.552 1.49,1.146 1.49,1.146 2.302,1.146 true 2.01,1.521 2.01,1.146 true 2.292,2.188 1.906,2.188 true 2.323,1.042 2.521,1.24 0.198,0.198 10 true *a 2.313,2.083 2.521,2.271 0.208,0.188 10 true *b
*a Guide A
*b Guide B
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull in the removal direction (1) shown in the illustration and detach the guide A.


b.

Detach the guide B in the removal direction (2) shown in the illustration and remove the outer lap belt anchor cover.


Hide 73220 12.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

a.
B541701

Remove the bolt and floor anchor of the front seat outer belt assembly LH.


Hide 73210 13.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)

HINT:

Use the same procedure described for the LH side.


Hide 74733 14.REMOVE NO. 1 HAND GRIP COVER (w/ Hand Rail)

Hide 74707 15.REMOVE NO. 1 HAND GRIP FRAME SUB-ASSEMBLY (w/ Hand Rail)

Hide 67917C 16.REMOVE REAR DOOR SCUFF PLATE RH

Hide 62312B 17.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Pull back the front door opening trim weatherstrip LH so that the quarter trim panel assembly LH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>REMOVAL


Hide 62311B 18.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
·

Pull back the front door opening trim weatherstrip RH so that the lower center pillar garnish RH and center piller garnish RH can be removed.

·

Use the same procedure described for the LH side.



Hide 67871E 19.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH

HINT:

Pull back the No. 1 slide door weatherstrip RH so that the lower center pillar garnish RH and center piller garnish RH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (except Wagon)>REMOVAL


Hide 62413A 20.REMOVE LOWER CENTER PILLAR GARNISH RH

Hide 21.REMOVE REAR SEAT ASSEMBLY LH

Hide 22.REMOVE REAR SEAT ASSEMBLY RH

a.

for Commuter, Single-Passenger Seat with 3-Point Type Seat Belt:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, Single-Passenger Seat with 3-Point Type Seat Belt)>REMOVAL


Hide 73570B 24.REMOVE REAR SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR) (w/ Seat Belt)

Hide 62640M 26.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY LH

Hide 62620K 27.REMOVE SIDE TRIM BOARD ASSEMBLY LH (for High Roof)

Hide 62520B 28.REMOVE QUARTER TRIM PANEL ASSEMBLY LH

Hide 73178C 29.REMOVE SEAT BELT ANCHOR COVER CAP

HINT:

Use the same procedure for the other side.


a.
B541702C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, using moulding remover A, detach the claw while pulling in the removal direction and remove the seat belt anchor cover cap.


Hide 73220 30.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B541704

Remove the bolt and shoulder anchor of the front seat outer belt assembly LH.


b.

w/ Pretensioner and Force Limiter:

i.
B541705C01
0.583,0.698 1.042,0.99 true 0.396,0.542 0.573,0.74 0.177,0.198 10 false *a
*a Locking Button
V113147

Release in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.




c.
B541707

Remove the 2 bolts.


d.

Detach the guide and remove the front seat outer belt assembly LH.


Hide 73210 31.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62411 32.REMOVE CENTER PILLAR GARNISH RH

HINT:

Perform this procedure when replacing the front shoulder belt anchor plate sub-assembly RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 62412 33.REMOVE CENTER PILLAR GARNISH LH

HINT:

Perform this procedure when replacing the front shoulder belt anchor plate sub-assembly LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 73024 34.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

HINT:

Perform this procedure when replacing the front shoulder belt anchor plate sub-assembly LH.


a.
B541743

Detach the guide and remove the front shoulder belt anchor plate sub-assembly LH.


Hide 73023 35.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
·

Perform this procedure when replacing the front shoulder belt anchor plate sub-assembly RH.

·

Use the same procedure described for the LH side.



Hide 73200A 36.REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

HINT:
·

Perform this procedure when replacing the front shoulder belt anchor adjuster assembly.

·

Use the same procedure for the other side.



a.
B541708

Remove the 2 bolts.


b.

Detach the guide and remove the front shoulder belt anchor adjuster assembly.