Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY (for Full-trim)
RM35X0E _58 Vehicle Interior _078602 SEAT BELT _0387529 FRONT SEAT OUTER BELT ASSEMBLY(for Full-trim) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for Full-trim)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 73200A 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

HINT:

Use the same procedure for the other side.


a.
B541708

Attach the guide.


b.

Install the front shoulder belt anchor adjuster assembly with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73024 2.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

a.
B541743

Attach the guide and install the front shoulder belt anchor plate sub-assembly LH.


Hide 73023 3.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73220 7.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B541707N01
2.115,0.917 2.271,1.115 0.156,0.198 10 true A 2.271,0.917 2.49,1.115 0.219,0.198 10 true (1) 2.313,2.979 2.469,3.177 0.156,0.198 10 true B 2.469,2.979 2.688,3.177 0.219,0.198 10 true (2)

Attach the guide.


b.

Temporarily install the front seat outer belt assembly LH with the 2 bolts.


c.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
Bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)


d.
B541706C01
2.271,0.708 2.771,0.979 true 2.073,0.552 2.26,0.729 0.188,0.177 10 false *a
*a Locking Button
V113147

Lock in this Direction


w/ Pretensioner and Force Limiter:

i.

Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:
·

When handling the pretensioner connector, take care not to damage the pretensioner wire harness.

·

Securely lock the locking button.





e.
B541704

Install the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73210 8.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73178C 9.INSTALL SEAT BELT ANCHOR COVER CAP

HINT:

Use the same procedure for the other side.


a.
B541703C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the seat belt anchor cover cap as shown in the illustration.


Hide 62520B 10.INSTALL QUARTER TRIM PANEL ASSEMBLY LH

Hide 62620K 11.INSTALL SIDE TRIM BOARD ASSEMBLY LH (for High Roof)

Hide 62640M 12.INSTALL REAR QUARTER TRIM BOARD ASSEMBLY LH

Hide 73570B 14.INSTALL REAR SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR) (w/ Seat Belt)

HINT:

Use the same procedure for the other side.

Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY (for Full-trim)>INSTALLATION


Hide 16.INSTALL REAR SEAT ASSEMBLY LH

Hide 17.INSTALL REAR SEAT ASSEMBLY RH

a.

for Commuter, Single-Passenger Seat with 3-Point Type Seat Belt:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 2-Passenger Seat with 3-Point Type Seat Belt)>INSTALLATION


Hide 62413A 18.INSTALL LOWER CENTER PILLAR GARNISH RH

Hide 67871E 19.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP RH

Hide 62312B 20.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 21.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 74707 23.INSTALL NO. 1 HAND GRIP FRAME SUB-ASSEMBLY (w/ Hand Rail)

Hide 74733 24.INSTALL NO. 1 HAND GRIP COVER (w/ Hand Rail)

Hide 73220 25.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

a.
B541701

Install the floor anchor of the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Check that the ELR locks.

i.

With the front seat outer belt assembly LH installed to the vehicle, check that the belt locks when it is pulled out quickly.



Hide 73210 26.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)

HINT:

Use the same procedure described for the LH side.


Hide 73233 27.INSTALL OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for the other side.


a.
B541700C01
1.49,1.552 1.49,1.146 1.49,1.146 2.302,1.146 true 2.01,1.521 2.01,1.146 true 2.292,2.188 1.906,2.188 true 2.323,1.042 2.521,1.24 0.198,0.198 10 true *a 2.313,2.083 2.521,2.271 0.208,0.188 10 true *b
*a Guide A
*b Guide B
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide B in the installation direction (1) shown in the illustration.


b.

Attach the guide A in the installation direction (2) shown in the illustration and install the outer lap belt anchor cover.


Hide 74680 28.INSTALL PILLAR ASSIST GRIP ASSEMBLY B (w/ Assist Grip)

Hide 74617A 29.INSTALL ASSIST GRIP PLUG (w/ Assist Grip)

Hide 31.INSTALL FRONT SEAT ASSEMBLY RH

a.

for Separate Seat Type:

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Separate Seat Type)>INSTALLATION





Hide 67914B 32.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 67913B 33.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 67912A 34.INSTALL FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67911B 35.INSTALL FRONT DOOR OUTSIDE SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 36.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Pretensioner and Force Limiter)

Hide 37. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (w/ Pretensioner and Force Limiter)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 38. PERFORM DIAGNOSTIC SYSTEM CHECK (w/ Pretensioner and Force Limiter)

Hide 40.INSPECT SEAT BELT WARNING SYSTEM (w/ Seat Belt Warning System)