Home › Drivetrain › CLUTCH › CLUTCH PEDAL
RM35X0E _52 Drivetrain _078837 CLUTCH _0382376 CLUTCH PEDAL N

CLUTCH  CLUTCH PEDAL  ADJUSTMENT  


PROCEDURE

Hide 55641 1.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER

Hide 2.INSPECT AND ADJUST CLUTCH PEDAL ASSEMBLY

a.

Fold back the floor carpet.


b.

Check that the clutch pedal height is correct.

C410830C01
5.688,0.646 5.99,0.427 5.99,0.427 6.167,0.427 true 2.885,2.021 3.385,2.021 true 5.167,0.615 4.688,0.156 4.688,0.156 4.5,0.156 true 5.99,1.781 6.313,1.344 6.313,1.344 6.552,1.344 true 6.229,0.365 6.542,0.563 0.313,0.198 10 false *d 5.958,2.271 6.271,2.469 0.313,0.198 10 false *a 2.375,1.729 2.604,1.927 0.229,0.198 10 true *a 3.438,1.927 3.667,2.156 0.229,0.229 10 true *b 1.115,1.125 1.365,1.375 0.25,0.25 10 true *c 5.771,1.24 6.083,1.438 0.313,0.198 10 false *e 4.323,0.063 4.635,0.26 0.313,0.198 10 false *f 6.594,1.26 6.906,1.458 0.313,0.198 10 false *1
*1 Clutch Pedal Pad - -
*a Clutch Pedal Height *b Measuring Plane of Floor Panel
*c 30 mm (1.18 in.) *d Pedal Height Adjustment Point
*e Push Rod Play *f Push Rod Play Adjustment Point


Clutch pedal height from floor panel:
for LHD:

244.6 to 258.6 mm (9.63 to 10.18 in.)

for RHD:

242.9 to 256.9 mm (9.57 to 10.11 in.)



c.

Adjust the clutch pedal height.

i.

Loosen the lock nut of the stopper bolt and the clutch switch. Then turn the clutch switch backward.


ii.

Turn the stopper bolt until the pedal height is within the specified range.


iii.

Tighten the lock nut of the stopper bolt.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


iv.

Adjust the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSTALLATION



d.
D031462C07
1.844,1.604 2.073,1.792 0.229,0.188 10 false *a 1.885,1.927 2.146,2.115 0.26,0.188 10 false *b
*a Push Rod Play
*b Pedal Free Play


Check the clutch pedal free play and push rod play.

HINT:

Pay close attention to the change in resistance to distinguish between pedal free play and push rod play while performing the inspection.


i.

Depress the clutch pedal until resistance is felt.


ii.

Measure the distance between the position of the pedal when it is released and the position in the previous step.

Standard pedal free play:

5.0 to 15.0 mm (0.197 to 0.591 in.)



iii.

Release the pedal. Using your finger, gently press the pedal until resistance increases slightly.


iv.

Measure the distance between the position of the pedal when it is released and the position in the previous step.

Standard push rod play at pedal top:

1.0 to 5.0 mm (0.0394 to 0.196 in.)




e.

Adjust the clutch pedal free play and push rod play.

HINT:

The push rod play can be adjusted by changing the length of the push rod. Pedal free play changes together with push rod play.


i.

Loosen the lock nut and turn the push rod until the pedal free play and push rod play are within the specified range.

NOTICE:

If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.



ii.

Tighten the lock nut.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


iii.

After adjusting the pedal free play and push rod play, check the pedal height.



f.
C227877C07
1.365,1.177 1.615,1.177 false 1.615,1.583 2.281,1.042 2.281,1.042 2.396,1.042 true 1.354,1.521 0.906,1.885 0.906,1.885 0.802,1.885 true 1.781,1.896 2.021,2.104 0.24,0.208 10 false *c 0.594,1.802 0.854,2.01 0.26,0.208 10 false *d 2.438,0.927 2.74,1.177 0.302,0.25 10 false *b 1.385,0.958 1.646,1.188 0.26,0.229 10 false *a
*a Distance from Clutch Pedal Stroke End Position to Release Point
*b Release Point
*c Clutch Pedal Stroke
*d Full Stroke End Position


Check the clutch release point.

CAUTION:

When checking the clutch release point, ensure that the vehicle is secure.


i.

Pull the parking brake lever and use wheel chocks to stabilize the vehicle.


ii.

Start the engine and run it at idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever to R until the gears contact each other.


iv.

Gently depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard distance A:

25 mm (0.984 in.) or more


Clutch pedal stroke at 200 N (20 kgf, 45.0 lbf):
Reference value:

153 to 163 mm (6.03 to 6.41 in.)


If the distance is not as specified, perform the following operations.

·

Check clutch pedal height.

·

Check push rod play and clutch pedal free play.

·

Bleed air from clutch line.

·

Check clutch cover and clutch disc.




Hide 89280 3.ADJUST CLUTCH PEDAL STROKE SENSOR ASSEMBLY

Hide 55641 4.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER