Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
55301
1.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
When installing a new instrument panel sub-assembly:
Immediately before installing the instrument panel sub-assembly, twist and cut off the portion as shown in the illustration.
for LHD:
Push in the direction indicated by the arrow shown in the illustration and insert the guide to set the instrument panel sub-assembly.
|
Install in this Direction | - | - |
Install the instrument panel sub-assembly with the 7 bolts <B>, nut <G> and 2 clips <F>.
|
Bolt <B> |
|
Nut <G> |
|
Clip <F> | - | - |
|
Bolt <D> |
Install the 2 bolts <D>.
Attach the claw to install the DLC3.
|
Install in this Direction |
Attach the claw to install the connector holder as shown in the illustration.
w/Telematics Transceiver:
Connect the connector.
Connect the connector and attach the clamp.
| *A | w/ Solar Sensor |
| *B | w/ Front Passenger Airbag |
| *C | w/ Parking Assist Monitor System |
Connect each connector.
for RHD:
Push in the direction indicated by the arrow shown in the illustration and insert the guide to set the instrument panel sub-assembly.
|
Install in this Direction | - | - |
Install the instrument panel sub-assembly with the 7 bolts <B>, nut <G> and 2 clips <F>.
|
Bolt <B> |
|
Nut <G> |
|
Clip <F> | - | - |
|
Bolt <D> |
Install the 2 bolts <D>.
Attach the claw to install the DLC3.
Connect the connector and attach the clamp.
| *A | w/ Solar Sensor or w/ Blind Spot Monitor System |
| *B | w/ Front Passenger Airbag |
| *C | w/ Parking Assist Monitor System |
Connect each connector.
2.INSTALL TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY (for Automatic Transmission)
62212
3.INSTALL FRONT PILLAR GARNISH LH
62211
4.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
74680
5.INSTALL PILLAR ASSIST GRIP ASSEMBLY LH
74680
6.INSTALL PILLAR ASSIST GRIP ASSEMBLY RH
Use the same procedure described for the LH side.
62312B
7.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Install the front door opening trim weatherstrip LH.
62311B
8.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
55314A
9.INSTALL CENTER LOWER INSTRUMENT PANEL (for Semi-trim)
When installing a new center lower instrument panel:
Immediately before installing the center lower instrument panel, twist and cut off the portion as shown in the illustration.
for Automatic Transmission:
|
Install in this Direction |
Attach the claw to install the center lower instrument panel.
for Manual Transmission:
|
Install in this Direction |
Attach the claw to install the center lower instrument panel.
|
Screw <C> |
Install the screw <C>.
55314A
10.INSTALL CENTER LOWER INSTRUMENT PANEL (for Full-trim)
When installing a new center lower instrument panel:
Immediately before installing the center lower instrument panel, twist and cut off the portion as shown in the illustration.
for Automatic Transmission:
|
Install in this Direction |
Attach the claw to install the center lower instrument panel.
for Manual Transmission:
|
Install in this Direction |
Attach the claw to install the center lower instrument panel.
|
Screw <C> |
Install the screw <C>.
55476A
11.INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
Install in this Direction |
Attach the guide and claw to install the No. 3 instrument cluster finish panel garnish as shown in the illustration.
55447C
12.INSTALL NO. 2 SWITCH HOLE BASE
Connect each connector.
|
Install in this Direction |
Attach the claw to install the No. 2 switch hole base as shown in the illustration.
55446A
13.INSTALL NO. 1 SWITCH HOLE BASE
|
Install in this Direction |
Attach the claw to install the No. 1 switch hole base as shown in the illustration.
55680A
14.INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Install in this Direction |
Attach the claw to install the No. 4 instrument panel register assembly as shown in the illustration.
55670
15.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
Connect the connector.
|
Install in this Direction |
Attach the claw to install the No. 3 instrument panel register assembly as shown in the illustration.
83100
16.INSTALL COMBINATION METER ASSEMBLY
55404E
17.INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
|
Install in this Direction |
Attach the guide and claw.
|
Install in this Direction |
Attach the guide and claw to install the upper instrument cluster finish panel sub-assembly.
55413D
18.INSTALL CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL
for Semi-trim:
|
Install in this Direction |
Attach the claw to install the center lower instrument cluster finish panel.
for Full-trim:
|
Install in this Direction |
Attach the claw to install the center lower instrument cluster finish panel.
55414A
19.INSTALL INSTRUMENT CLUSTER FINISH PANEL END (for Semi-trim)
|
Install in this Direction |
Attach the claw to install the instrument cluster finish panel end.
55320
20.INSTALL LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY
|
Install in this Direction |
Attach the claw to install the lower No. 2 instrument panel assembly.
Open the glove compartment door assembly.
|
Bolt <B> |
Install the 5 bolts <B>.
Attach the claw to install the instrument panel box door knob.
Close the glove compartment door assembly.
55434B
21.INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL
for Semi-trim:
|
Install in this Direction |
Attach the guide and claw to install the center lower instrument panel finish panel.
|
Bolt <B> |
Install the bolt <B>.
for Full-trim:
|
Install in this Direction |
Attach the guide and claw to install the center lower instrument panel finish panel.
|
Bolt <B> |
Install the bolt <B>.
22.INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/ Radio Receiver Opening Cover)
|
Install in this Direction |
Attach the guide to install the radio tuner opening cover with bracket as shown in the illustration.
Install the 2 bolts.
Install the 2 bolts.
23.INSTALL DISPLAY AND NAVIGATION ASSEMBLY WITH BRACKET (w/ Navigation System)
24.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
25.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)
55410C
26.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
|
Install in this Direction |
Attach the claw to install the instrument cluster finish panel assembly.
55900
27.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
Connect each connector.
|
Install in this Direction |
Attach the claw to install the air conditioning control assembly.
55405B
28.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)
for Semi-trim:
Attach the guide and claw to install the No. 2 heater control cable sub-assembly and air mix damper control cable sub-assembly.
Connect each connector.
|
Install in this Direction |
Attach the claw to install the center instrument cluster finish panel sub-assembly.
for Full-trim:
| *A | for LHD |
| *B | for RHD |
| *a | Heater Control Knob |
Attach the guide and claw to install the No. 2 heater control cable sub-assembly and air mix damper control cable sub-assembly.
Connect each connector.
| Location | Color |
|---|---|
| Heater Control Knob x Wire Harness Connector | Gray |
|
Install in this Direction |
Attach the claw to install the center instrument cluster finish panel sub-assembly.
35970F
29.INSTALL POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transmission)
for Semi-trim:
Connect the connector.
|
Install in this Direction |
Attach the clip and claw to install the position indicator housing assembly.
for Full-trim:
Connect the connector.
|
Install in this Direction |
Attach the clip and claw to install the position indicator housing assembly.
58840Q
30.INSTALL SHIFTING HOLE COVER ASSEMBLY (for Manual Transmission)
for Semi-trim:
|
Install in this Direction |
Attach the claw to install the shifting hole cover assembly.
for Full-trim:
|
Install in this Direction |
Attach the claw to install the shifting hole cover assembly.
33504F
31.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transmission)
33622
32.INSTALL NO. 1 SHIFT LEVER KNOB COVER (for Automatic Transmission)
33504F
33.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)
|
Install in this Direction |
Twist the shift lever knob sub-assembly in the direction indicated by the arrow to install it.
55646
34.INSTALL NO. 3 INSTRUMENT PANEL UNDER COVER
w/o Console Tray:
Connect each connector.
|
Install in this Direction |
Attach the clip and claw to install the No. 3 instrument panel under cover.
w/ Console Tray:
Connect each connector.
|
Install in this Direction |
Attach the clip and claw to install the No. 3 instrument panel under cover.
58534E
35.INSTALL CENTER FLOOR CARPET COVER LH
for LHD:
|
Insert in this Direction |
Insert the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the claw to install the center floor carpet cover LH.
for RHD:
|
Insert in this Direction |
Insert the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the claw to install the center floor carpet cover LH.
58533C
36.INSTALL CENTER FLOOR CARPET COVER RH
for LHD:
|
Install in this Direction |
Attach the guide, claw and clip to install the center floor carpet cover RH.
for RHD:
|
Install in this Direction |
Attach the guide, claw and clip to install the center floor carpet cover RH.
37.INSTALL FRONT CONSOLE BOX (w/ Console Tray)
73900
38.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
55313
39.INSTALL LOWER INSTRUMENT PANEL LH (w/o Knee Airbag)
Attach the guide to set the lower instrument panel LH.
|
Bolt <E> |
Install the lower instrument panel LH with the 3 bolts <E>.
55445B
40.INSTALL INSTRUMENT PANEL FINISH PLATE (w/o Knee Airbag)
|
Install in this Direction |
Attach the claw to install the instrument panel finish plate.
55433B
41.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
for Automatic Air Conditioning System:
|
Connector |
|
Aspirator Hose |
Connect the connector and aspirator hose.
|
Install in this Direction |
Attach the guide and claw to install the lower No. 2 instrument panel finish panel.
|
Screw <A> |
Install the screw <A>.
55044C
42.INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
|
Install in this Direction |
Attach the claw to install the instrument panel finish panel sub-assembly.
55432D
43.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
Connect each connector.
|
Install in this Direction |
Attach the claw to install the lower No. 1 instrument panel finish panel.
|
Screw <A> |
Install the 2 screws <A>.
77306
44.INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
|
Install in this Direction |
Attach the guide and claw to install the fuel lid lock open lever sub-assembly in the direction indicated by the arrow shown in the illustration.
53601
45.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
|
Install in this Direction |
Attach the guide and claw to install the hood lock control lever sub-assembly in the direction indicated by the arrow shown in the illustration.
55641
46.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER
for LHD:
w/ Tire Pressure Warning System:
Connect the connector.
|
Insert in this Direction |
Insert the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the clip and claw to install the No. 1 instrument panel under cover shown in the illustration.
|
Screw <A> |
Install the 3 screws <A>.
for RHD:
|
Insert in this Direction |
Insert the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the clip and claw to install the No. 1 instrument panel under cover shown in the illustration.
|
Screw <A> |
Install the 3 screws <A>.
55318C
47.INSTALL INSTRUMENT SIDE PANEL LH
|
Insert in this Direction |
Insert in the direction indicated by the arrow shown in the illustration to attach the guide.
|
Install in this Direction |
Attach the guide and claw to install the instrument side panel LH as shown in the illustration.
55011A
48.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
w/ Power Slide Door:
Connect each connector.
|
Install in this Direction |
Attach the guide and claw to install the No. 1 instrument panel garnish sub-assembly.
|
Screw <A> |
Install the screw <A>.
55631A
49.INSTALL NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER
Install the No. 1 instrument panel under tray stopper.
62112
50.INSTALL COWL SIDE TRIM BOARD LH
|
Install in this Direction |
Attach the guide, claw and clip to install the cowl side trim board LH.
Install the cap nut.
67914B
51.INSTALL FRONT DOOR SCUFF PLATE LH
67912A
52.INSTALL FRONT DOOR OUTSIDE SCUFF PLATE LH
55438A
53.INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL RETAINER
|
Install in this Direction |
Attach the claw to install the No. 2 instrument panel finish panel retainer as shown in the illustration.
55312
54.INSTALL LOWER INSTRUMENT PANEL
|
Install in this Direction |
Attach the guide as shown in the illustration.
|
Install in this Direction |
Attach the clip to install the lower instrument panel.
|
Slide in this Direction |
Open the glove compartment door and slide the instrument panel box lock knob in the direction of the arrow shown in the illustration.
55642
55.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER
|
Insert in this Direction |
Insert the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Lift up in the direction indicated by the arrow shown in the illustration to attach the claw to install the No. 2 instrument panel under cover.
55317A
56.INSTALL INSTRUMENT SIDE PANEL RH
|
Insert in this Direction |
Insert in the direction indicated by the arrow shown in the illustration to attach the guide.
|
Install in this Direction |
Attach the guide and claw to install the instrument side panel RH as shown in the illustration.
55012A
57.INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
|
Install in this Direction |
Attach the guide and claw to install the No. 2 instrument panel garnish sub-assembly.
|
Screw <A> |
Install the screw <A>.
55632B
58.INSTALL NO. 2 INSTRUMENT PANEL UNDER TRAY SUPPORT
Install the No. 2 instrument panel under tray support.
62111C
59.INSTALL COWL SIDE TRIM BOARD RH
|
Install in this Direction |
Attach the guide, claw and clip to install the cowl side trim board RH.
Install the cap nut.
67913B
60.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>INSTALLATION
67911B
61.INSTALL FRONT DOOR OUTSIDE SCUFF PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>INSTALLATION
62.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
63. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (w/ Airbag System)
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
64. PERFORM DIAGNOSTIC SYSTEM CHECK
65.CHECK SRS WARNING LIGHT
66.PERFORM SYSTEM INITIALIZATION AND CALIBRATION