Home › Vehicle Exterior › WINDOW / GLASS › FRONT SIDE WINDOW GLASS › 2019.02–2019.06
RM35X0E _59 Vehicle Exterior _079318 WINDOW / GLASS _0388651 FRONT SIDE WINDOW GLASS A

WINDOW / GLASS  FRONT SIDE WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or equivalent.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR SEAT ASSEMBLY

·
·
·

for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt)>REMOVAL

·

for Commuter, Single-Passenger Seat with 3-Point Type Seat Belt:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, Single-Passenger Seat with 3-Point Type Seat Belt)>REMOVAL

·
·

for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt and Headrest:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt and Headrest)>REMOVAL

·

for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest)>REMOVAL


Hide 67912A 2.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH (for Full-trim)

Hide 67914B 3.REMOVE FRONT DOOR SCUFF PLATE LH (for Full-trim)

Hide 73178C 4.REMOVE SEAT BELT ANCHOR COVER CAP (for Full-trim)

Hide 73233 5.REMOVE OUTER LAP BELT ANCHOR COVER (for Full-trim)

Hide 73220 6.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (for Full-trim)

Hide 73370E 7.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (for Full-trim, w/ Seat Belt)

Hide 58777A 8.REMOVE TOOL BAG HOLDER (for Full-trim)

Hide 67935 9.REMOVE BACK DOOR SCUFF PLATE (for Full-trim)

Hide 62640M 10.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY LH (for Full-trim, for High Roof)

Hide 62620K 11.REMOVE SIDE TRIM BOARD ASSEMBLY LH (for Full-trim, for High Roof)

Hide 62520B 12.REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for Full-trim)

Hide 62472D 13.REMOVE REAR UPPER PILLAR GARNISH LH (for Full-trim)

Hide 62639A 14.REMOVE QUARTER PILLAR GARNISH LH (for Full-trim)

Hide 62639A 15.REMOVE QUARTER PILLAR GARNISH LH (for Full-trim, for High Roof)

HINT:

Use the same procedure for the quarter pillar garnish RH.


Hide 62412 16.REMOVE CENTER PILLAR GARNISH ASSEMBLY LH (for Full-trim)

Hide 62460A 17.REMOVE REAR ROOF SIDE RAIL GARNISH ASSEMBLY LH (for Full-trim)

Hide 62440D 18.REMOVE FRONT ROOF SIDE RAIL GARNISH ASSEMBLY LH (for Full-trim)

Hide 19.REMOVE ROOF HEADLINING ASSEMBLY (for Semi-trim, for High Roof, w/ Rear Air Duct)

Hide 62720C 20.REMOVE FRONT SIDE WINDOW GLASS SUB-ASSEMBLY LH

a.
B541089C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the front side window glass sub-assembly LH from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



b.
B541090C01
1.719,0.375 2.177,0.188 2.177,0.188 1.729,0.781 true 2.219,0.104 2.531,0.302 0.313,0.198 10 false *a
*a Matchmark


When reusing the front side window glass sub-assembly LH:

i.

Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.


ii.

Install the suction cups to the front side window glass sub-assembly LH.



c.
B541091C01
1.708,1.875 1.5,1.635 true 0.656,0.74 1.167,0.833 true 2.51,0.708 1.99,0.854 true 2.5,1.552 2.063,1.365 true 1.219,1.302 0.896,1.448 true 1.781,0.813 1.969,1.021 0.188,0.208 10 true *1 1.271,1.167 1.448,1.365 0.177,0.198 10 true *2 1.719,1.896 2.031,2.094 0.313,0.198 10 true *a 1.854,1.24 2.031,1.438 0.177,0.198 10 true *2 1.24,0.802 1.427,1.01 0.188,0.208 10 true *1
*1 Quarter Window Glass Spacer
*2 Front Side Window Clip LH
*a Piano Wire


From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


d.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:

When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



e.

Cut through the adhesive by pulling the piano wire around the front side window glass sub-assembly LH.


f.

Using suction cups, disconnect the quarter window glass spacer and front side window clip LH and remove the front side window glass sub-assembly LH.

NOTICE:

Do not drop the front side window glass sub-assembly LH.



Hide 21.REMOVE NO. 1 QUARTER PANEL SPACER

a.
B541103

Using a clip remover, remove the 2 No. 1 quarter panel spacers from the body.