Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for Semi-trim) › 2019.02–2019.06
RM35X0E _58 Vehicle Interior _078375 INTERIOR PANELS / TRIM _0380060 ROOF HEADLINING(for Semi-trim) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Semi-trim)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the roof headlining assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION (w/ Airbag System)

CAUTION:
B407254

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 61890A 3.REMOVE BACK WINDOW GLASS HAMMER ASSEMBLY (w/ Hammer)

Hide 67912A 4.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67914B 5.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67911B 6.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 67913B 7.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 9.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 11.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 74680 12.REMOVE PILLAR ASSIST GRIP ASSEMBLY LH

Hide 74680 13.REMOVE PILLAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62211 15.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 17.REMOVE REAR SEAT ASSEMBLY LH

Hide 18.REMOVE REAR SEAT ASSEMBLY RH

a.

for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt)>REMOVAL


b.

for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest:

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest)>REMOVAL



Hide 74617A 19.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)

Hide 74680 20.REMOVE PILLAR ASSIST GRIP ASSEMBLY B (w/ Assist Grip)

Hide 73178C 21.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 73233 22.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73220 23.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73210 24.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74733 25.REMOVE NO. 1 HAND GRIP COVER (w/ Hand Rail)

a.
B519220

Detach the clip and remove the No. 1 hand grip cover.


Hide 74707 26.REMOVE NO. 1 HAND GRIP FRAME SUB-ASSEMBLY (w/ Hand Rail)

a.
B519221

Remove the 6 bolts.


b.

Detach the guide and remove the No. 1 hand frame grip sub-assembly.


Hide 67917C 27.REMOVE REAR DOOR SCUFF PLATE RH


b.

for Standard Roof, except Full Cover Type:

i.
B519251

Remove the 5 screws.


ii.
B519252

Detach the clip and guide and remove the rear door scuff plate RH.




d.

for High Roof, except Full Cover Type:

i.
B519253

Remove the 6 screws.


ii.
B519254

Detach the clip and guide and remove the rear door scuff plate RH.



Hide 67918D 28.REMOVE REAR DOOR SCUFF PLATE LH (for 5 Door)

HINT:

Use the same procedure described for the RH side.


Hide 67871E 29.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH

HINT:

Pull back the No. 1 slide door weatherstrip RH so that the lower center pillar garnish RH and center pillar garnish RH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (except Wagon)>REMOVAL


Hide 67872A 30.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH (for 5 Door)

HINT:
·

Pull back the No. 1 slide weatherstrip LH so that the lower center pillar garnish LH and center pillar garnish LH can be removed.

·

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (except Wagon)>REMOVAL



Hide 62413A 31.REMOVE LOWER CENTER PILLAR GARNISH RH

Hide 62414A 32.REMOVE LOWER CENTER PILLAR GARNISH LH

HINT:

Use the same procedure described for the RH side.


Hide 62411 33.REMOVE CENTER PILLAR GARNISH RH

Hide 62412 34.REMOVE CENTER PILLAR GARNISH LH

a.

for 4 Door, Standard Roof:

i.
B519217

Remove the clip.


ii.
B519218

Detach the clip.


iii.
B519219C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the center pillar garnish LH.



b.

for 4 Door, High Roof:

i.
B539653

Remove the clip.


ii.
B539654

Detach the clip.


iii.
B539655C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place both hands at the position shown in the illustration, pull in the direction indicated by the arrow to detach the clip and remove the center pillar garnish LH.



c.

for 5 Door:

HINT:

Use the same procedure described for the RH side.



Hide 73370E 35.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (for Van, w/ Seat Belt)

a.
B541711C01
0,0 0,0 false
V113147

Open in this Direction


Using moulding remover D, detach the claw and open the cover as shown in the illustration.


b.
B541713

Remove the bolt.


Hide 73360D 36.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (for Van, w/ Seat Belt)

HINT:

Use the same procedure described for the LH side.


Hide 81240 37.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 81240D 38.REMOVE NO. 2 ROOM LIGHT ASSEMBLY (for High Roof, w/ No. 2 Room Light Assembly)

HINT:

Use the same procedure described for the No. 1 room light assembly.


Hide 63349A 39.REMOVE REAR ROOF HEADLINING GARNISH (w/ Roof Window Glass)


b.

w/o Rear Air Duct:

i.
B539639C01
0,0 0,0 false
V113147

Pull in this Direction


Insert moulding remover D at the position shown in the illustration.


ii.
B539640C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand into the gap and pull as shown to detach the clip.



c.
B539600C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.


d.
B539601C01
0,0 0,0 false
V113147

Remove in this Direction


Pull in the direction of the arrow shown in the illustration to detach the clip and remove the rear roof headlining garnish.


Hide 72681E 40.REMOVE REAR SEAT HOOK (for High Roof, w/ Seat Hook)

Hide 63320E 41.REMOVE REAR ROOF HEADLINING ASSEMBLY (for Standard Roof)

a.
B539619C01
1.698,0.417 1.833,0.208 1.833,0.208 2.083,0.208 false 2.135,0.135 2.448,0.333 0.313,0.198 10 false *a
*a Plate
V100136

w/ Plate


Remove the 16 clips and 2 plates.

HINT:

The clips indicated by the white arrow have plates between the rear roof headlining assembly and body. Be careful not to let them fall.



b.

Detach the guide and remove the rear roof headlining assembly.


c.
B539621

Turn the rear roof headlining assembly diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure that wrinkles do not form in the rear roof headlining assembly during removal.

·

Make sure that the rear roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the rear roof headlining assembly or vehicle interior.

·

2 or more people are required when carrying the rear roof headlining assembly out of the vehicle, as it may become deformed.




Hide 63320E 42.REMOVE REAR ROOF HEADLINING ASSEMBLY (for High Roof)

a.

w/o Rear Air Duct:

i.

w/ Roof Window Glass:

Remove the 23 clips, 4 plates and rear roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the rear roof headlining assembly and body. Be careful not to let them fall.


B539641C01
6.063,1.302 6.229,0.938 6.229,0.938 6.479,0.938 false 6.521,0.865 6.833,1.063 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -



ii.

w/o Roof Window Glass:

Remove the 25 clips, 4 plates and rear roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the rear roof headlining assembly and body. Be careful not to let them fall.


B539642C01
6.083,1.333 6.167,1 6.167,1 6.417,1 false 6.479,0.917 6.792,1.115 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -




b.

w/ Rear Air Duct:

i.

w/ Roof Window Glass:

Remove the 29 clips, 4 plates and rear roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the rear roof headlining assembly and body. Be careful not to let them fall.


B539643C01
5.958,0.781 6.125,0.448 6.125,0.448 6.375,0.448 false 6.417,0.365 6.729,0.563 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -



ii.

w/o Roof Window Glass:

Remove the 26 clips, 4 plates and rear roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the rear roof headlining assembly and body. Be careful not to let them fall.


B539644C01
5.958,0.771 6.125,0.521 6.125,0.521 6.292,0.521 false 6.354,0.438 6.667,0.635 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -




c.
B539656

Turn the rear roof headlining assembly diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure that wrinkles do not form in the rear roof headlining assembly during removal.

·

Make sure that the rear roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the rear roof headlining assembly or vehicle interior.

·

2 or more people are required when carrying the rear roof headlining assembly out of the vehicle, as it may become deformed.




Hide 87834 43.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER

Hide 81260A 44.REMOVE MAP LIGHT ASSEMBLY

Hide 86466D 45.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

Hide 86768 46.REMOVE ROOF ANTENNA COVER (w/ Digital Audio Broadcasting Antenna)

Hide 47.REMOVE ASSIST GRIP ASSEMBLY (w/ Assist Grip)

Hide 74310 49.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 53989A 51.REMOVE AIR INTAKE NET (w/ Rear Air Duct)

Hide 65896J 52.REMOVE COVER TOP SET BOLT CAP (for Standard Roof, w/ Rear Air Duct)

Hide 63438F 53.REMOVE NO. 1 INNER ROOF RACK COVER (for High Roof)

Hide 63439D 54.REMOVE NO. 2 INNER ROOF RACK COVER (for High Roof)

Hide 63413C 55.REMOVE FRONT INNER ROOF RACK BOARD (for High Roof)

Hide 56.REMOVE ROOF HEADLINING ASSEMBLY (for Standard Roof)

a.

for Windshield Glass Side:

i.

Disconnect each connector.



b.

for Front Pillar LH Side:

i.

w/ Curtain Shield Airbag:

Remove the protective cover installed to the front pillar LH.


ii.
B539624C04
2.604,1.198 2.875,1.427 0.271,0.229 12 true *A
*A w/ Rear Wiper or w/ Digital Inner Mirror
V100135

Connector
V100136

Washer Hose


Disconnect the 3 connectors.


iii.

Using a clip remover, detach the wire harness clamp.


iv.

w/ Rear Wiper or w/ Digital Inner Mirror:

Disconnect the washer hose.


v.

w/ Curtain Shield Airbag:

Install the protective cover to the front pillar LH.



c.

for Rear Roof LH Side:

i.
B539625C01
0.479,1.708 0.76,1.948 0.281,0.24 12 true *A
*A w/ Rear Wiper or w/ Digital Inner Mirror
V100135

Connector
V100136

Washer Hose


Disconnect the connector.


ii.

w/ Rear Wiper or w/ Digital Inner Mirror:

Disconnect the washer hose.



d.

for Rear Roof RH Side, w/ Digital Inner Mirror:

i.
B539626

Detach the clamp and disconnect the connector.



e.

w/o Rear Air Duct, for 4 Door:

i.

Remove the 12 clips and 2 plates.

HINT:

The clips indicated by the white arrow have plates between the roof headlining assembly and body. Be careful not to let them fall.



ii.

Detach the fastener and remove the roof headlining assembly.

B539646C01
5.927,1.552 6.167,1.25 6.167,1.25 6.417,1.25 false 6.458,1.167 6.771,1.365 0.313,0.198 10 false *b 5.271,0.146 5.583,0.344 0.313,0.198 10 false *a
*a Fastener *b Plate
V100136

w/ Plate - -




f.

w/o Rear Air Duct, for 5 Door:

i.

Remove the 11 clips and 2 plates.

HINT:

The clips indicated by the white arrow have plates between the roof headlining assembly and body. Be careful not to let them fall.



ii.

Detach the fastener and remove the roof headlining assembly.

B539647C01
6.063,1.604 6.25,1.25 6.25,1.25 6.417,1.25 false 5.958,0.073 6.271,0.271 0.313,0.198 10 false *a 0.417,0.417 0.729,0.615 0.313,0.198 10 false *a 6.458,1.167 6.771,1.365 0.313,0.198 10 false *b
*a Fastener *b Plate
V100136

w/ Plate - -





h.
B539638

Turn the front roof headlining assembly diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure that wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.

·

2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.




Hide 57.REMOVE ROOF HEADLINING ASSEMBLY (for High Roof)

a.

for Windshield Glass Side:

i.

Disconnect each connector.



b.

for Front Pillar LH Side:

i.

w/ Curtain Shield Airbag:

Remove the protective cover installed to the front pillar LH.


ii.
B539629C05
2.76,1.24 3.052,1.479 0.292,0.24 12 true *A
*A w/ Rear Wiper or w/ Digital Inner Mirror
V100135

Connector
V100136

Washer Hose


Disconnect the 3 connectors.


iii.

Using a clip remover, detach the wire harness clamp.


iv.

w/ Rear Wiper or w/ Digital Inner Mirror:

Disconnect the washer hose.


v.

w/ Curtain Shield Airbag:

Install the protective cover to the front pillar LH.



c.

for Rear Roof LH Side:

i.
B539648

Disconnect the connector.


ii.

w/ Rear Wiper or w/ Digital Inner Mirror:

Detach the clamp and disconnect the washer hose.

B539649



d.

for Rear Roof RH Side, w/ Digital Inner Mirror:

i.

Detach the clamp and disconnect the connector.

B539651



e.
B539632

for Roof Headlining Front Side:

i.

w/o Wire Harness Protector:

Detach the clamp.


ii.
B539650

w/ Wire Harness Protector:

Detach the clamp.



f.

w/ Rear Air Duct:

i.
B539633

Remove the 4 bolts.


ii.

Remove the 14 clips, 2 plates and roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the roof headlining assembly and body. Be careful not to let them fall.


B539652C01
6,0.885 6.167,0.552 6.167,0.552 6.333,0.552 true 6.396,0.469 6.708,0.667 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -




g.

w/o Rear Air Duct:

Remove the 16 clips, 2 plates and roof headlining assembly.

HINT:

The clips indicated by the white arrow have plates between the roof headlining assembly and body. Be careful not to let them fall.


B539658C01
5.854,1.281 6.021,0.948 6.021,0.948 6.188,0.948 true 6.26,0.854 6.573,1.052 0.313,0.198 10 false *a
*a Plate - -
V100136

w/ Plate - -



h.
B539657

Turn the front roof headlining assembly diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure that wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.

·

2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.




Hide 67935 58.REMOVE BACK DOOR SCUFF PLATE

HINT:

Perform this procedure only when replacing the back door scuff plate.


a.
B519225

Remove the 4 screws.


b.
B519226C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and remove the back door scuff plate as shown illustration.