Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR (for Sliding Bench Seat Type) › 2019.02–2019.06
RM35X0E _58 Vehicle Interior _078602 SEAT BELT _0389113 OCCUPANT DETECTION SENSOR(for Sliding Bench Seat Type) A

SEAT BELT  OCCUPANT DETECTION SENSOR(for Sliding Bench Seat Type)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat cushion pad (occupant detection sensor) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION (w/ Front Seat Side Airbag)

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 72329D 4.REMOVE SEAT ADJUSTER BOLT COVER RH

Hide 72525M 5.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

Hide 71811T 7.REMOVE FRONT SEAT CUSHION SHIELD RH

Hide 8.REMOVE FRONT SEAT CUSHION COVER WITH PAD

a.

Detach the hook.

B533387


b.
B548422

Detach the hook.


c.

w/o Center Seat Occupant Detection Sensor:

i.
B548424

Disconnect the connector.


ii.

Detach the clamp.



d.

w/ Center Seat Occupant Detection Sensor:

i.
B548425

Disconnect the 2 connectors.


ii.

Detach the clamp.



e.

Remove the front seat cushion cover with pad.


Hide 71511A 9.REMOVE FRONT SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)

a.
B535144

Remove the 11 hog rings and front seat cushion pad RH (occupant detection sensor).