25800
1.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY
Install a new gasket and the electric EGR control valve assembly to the EGR valve adapter sub-assembly with the 2 bolts.
Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.
Attach the clamp and connect the connector to the common rail assembly.
25612
2.INSTALL NO. 2 EGR PIPE
Install 2 new gaskets and the No. 2 EGR pipe to the electric EGR control valve assembly and intake manifold with the 4 nuts.
25625
3.INSTALL EGR VALVE BRACKET
Install the EGR valve bracket to the electric EGR control valve assembly and intake manifold with the bolt and nut.
82121
4.CONNECT ENGINE WIRE
Attach the clamp and connect the engine wire to the No. 4 water by-pass pipe sub-assembly with the bolt.
Attach the 2 clamps and connect the engine wire to the No. 3 water by-pass pipe sub-assembly and wire harness clamp bracket.
Connect the 2 connectors to the vane pump assembly.
Connect the connector to the sensor wire of the common rail assembly with the bolt.
Connect the connector to the glow plug connector.
Connect the connector to the electric EGR control valve assembly.
Connect the 4 connectors to the 4 injector assemblies.
Attach the 3 clamps and connect the engine wire to the 2 wire harness clamp brackets.
Connect the connector to the camshaft position sensor.
Attach the clamp and connect the connector to the intake mass air flow meter assembly.
Connect the 2 connectors to the turbocharger sub-assembly.
23941
5.CONNECT NO. 1 FUEL FILTER PROTECTOR
Connect the No. 1 fuel filter protector to the body.
Attach the clamp and connect the wire harness to the No. 1 fuel filter protector.
Connect the connector to the fuel filter assembly.
12632
6.INSTALL NO. 2 ENGINE COVER BRACKET
Install the No. 2 engine cover bracket to the No. 3 water by-pass pipe sub-assembly and EGR valve adapter sub-assembly with the 2 bolts.
23265C
7.INSTALL GAS FILTER
Attach the clamp and install the gas filter to the gas filter bracket.
Connect the vacuum hose to the intake manifold.
89421C
8.INSTALL DIESEL TURBO PRESSURE SENSOR
Connect the vacuum hose and install the diesel turbo pressure sensor to the No. 3 water by-pass pipe sub-assembly with the bolt.
Connect the connector to the diesel turbo pressure sensor.
16278
9.INSTALL NO. 2 WATER BY-PASS PIPE
Install the No. 2 water by-pass pipe to the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly with the 3 bolts.
Connect the No. 16 water by-pass hose to the EGR pipe stay, and slide the clamp to secure the hose.
Connect the No. 15 water by-pass hose to the water by-pass pipe, and slide the clamp to secure the hose.
w/ Heater:
Connect the No. 13 water by-pass hose to the No. 2 water by-pass pipe, and slide the clamp to secure the hose.
w/ Viscous Heater:
Connect the water by-pass hose sub-assembly to the No. 2 water by-pass pipe, and slide the clamp to secure the hose.
for Laminated EGR Pre-cooler:
Attach the clamp, connect the No. 18 water by-pass hose to the EGR pipe with cooler sub-assembly, and slide the clamp to secure the hose.
87209
10.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Heater)
w/o Rear Heater:
Install the 2 water hose sub-assemblies to the air conditioning unit assembly and No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.
w/ Rear Heater:
Install the 2 water hose sub-assemblies to the air conditioning unit assembly and No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.
Connect the 2 water hose sub-assemblies to the water pipe, and slide the 2 clamps to secure the hoses.
26100G
11.INSTALL DIESEL THROTTLE BODY ASSEMBLY
55701J
12.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
85110
13.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
14.ADD ENGINE COOLANT
15.INSPECT FOR COOLANT LEAK