The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on this signal.
| Malfunction Status | Factor |
|---|---|
| Refrigerant pressure does not decrease when temeprature switch is off. | Compressor with magnet clutch assembly circuit malfunction |
If DTC B1422 is output at the same time, troubleshoot for DTC B1422 first.
Using the GTS, check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
CAN communication system DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the magnet-clutch relay (FR MGC) from the No. 1 engine room relay block assembly.
Inspect the magnet-clutch relay (FR MGC).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the magnet clutch assembly.
Inspect the magnet clutch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the magnet-clutch relay (FR MGC) from the No. 1 engine room relay block assembly.
Disconnect the E15 compressor assembly with magnet clutch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 5 - E15-3 (MG+) | Always | Below 1 Ω |
| Terminal 5 or E15-3 (MG+) - Other terminals and body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Terminal 2 - Body ground | Ignition switch off | Below 1 V |
| Terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| Terminal 3 - Body ground | Ignition switch off | Below 1 V |
| Terminal 3 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the magnet-clutch relay (FR MGC) from the No. 1 engine room relay block assembly.
Disconnect the N41 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 1 - N41-19 (MGC) | Always | Below 1 Ω |
| Terminal 1 or N41-19 (MGC) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N41-19 (MGC) - Body ground | ·
Engine idling ·
Blower switch: On (LO level) ·
Temeprature switch: On (magnet clutch on) |
Below 1 V |
| N41-19 (MGC) - Body ground | ·
Engine idling ·
Blower switch: On (LO level) ·
Temperature switch: Off or on (magnet clutch off) |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG