The EGR system recirculates exhaust gases. The recirculated gas mingles with the intake air so that the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.
In order to increase EGR circulation efficiency, the ECM adjusts the EGR valve angle and the throttle valve angle.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P040000 | Exhaust Gas Recirculation "A" Flow | Mass air flow rate is not changed when turning on the electric EGR control valve assembly while decelerating (2 trip detection logic). | ·
EGR valve deposit ·
EGR valve passage deposit ·
Mass air flow meter sub-assembly |
Comes on | DTC stored | SAE Code: P0400 |
| DTC No. | Data List |
|---|---|
| P040000 | ·
Mass Air Flow Sensor ·
Target EGR Valve Position No.1 ·
Actual EGR Valve Position No.1 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P040000 | After warming up the engine, decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator pedal for approximately 5 seconds). |
If the EGR valve is forcibly operated during deceleration but the intake air amount does not vary, the ECM determines that the EGR valve is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P040000 is output | A |
| DTC P040000 and other DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.
| Tester Display |
|---|
| Mass Air Flow Sensor |
Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close Bank 1 / Data List / Mass Air Flow Sensor.
| Active Test Display |
|---|
| Activate the EGR Valve Close Bank 1 |
| Data List Display |
|---|
| Mass Air Flow Sensor |
Read the Mass Air Flow Sensor value when the EGR valve is closed using the Active Test function.
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
When idling the engine, the EGR cooler is bypassed.
| Active Test | Result | Proceed to |
|---|---|---|
| Activate the EGR Valve Close Bank 1:
OFF to Close |
Mass Air Flow Sensor value does not change | A |
| Mass Air Flow Sensor value changes | B |
As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.
| EGR Valve Condition (Opening) | Measuring Condition | Mass Air Flow Sensor (Reference) |
|---|---|---|
| Open (41%) | ·
Atmospheric pressure: 101 kPa ·
Engine coolant temperature: 75°C (167°F) |
3 to 7 gm/sec |
| Closed (0%) | 10 to 21 gm/sec |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Mass Air Flow Sensor.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
Start the engine and read the value when 30 seconds has elapsed.
| Engine Speed | Mass Air Flow Sensor |
|---|---|
| Idling | ·
0.5 to 15 gm/sec (EGR on) ·
10 to 21 gm/sec (EGR off) |
| 3000 rpm (without load) | ·
43 to 89 gm/sec (EGR on) ·
72 to 117 gm/sec (EGR off) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>REMOVAL
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
When cleaning the electric EGR control valve, make sure the valve is completely closed.
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
When cleaning the electric EGR control valve, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR valve.
When cleaning the electric EGR control valve assembly, perform the initialization procedure.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION
If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.
Reinstall the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up.
Move the shift lever to 2nd gear and decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator for approximately 5 seconds or more).
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
When a DTC is output, the mass air flow meter may be malfunctioning.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
| Proceed to |
|---|
| NEXT |
NEXT