The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the electric EGR control valve assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P040318 | Exhaust Gas Recirculation "A" Circuit Current Below Threshold | Both of the following conditions are met for 2.0 seconds (1 trip detection logic):
·
The EGR actuator duty cycle is 80% or higher. ·
EGR actuator current is below 0.5 A. |
·
Open or short in EGR actuator circuit ·
Electric EGR control valve assembly ·
ECM |
Comes on | DTC stored | SAE Code: P0489 |
| P040319 | Exhaust Gas Recirculation "A" Circuit Current Above Threshold | Either of the following conditions is met for 2.0 seconds (1 trip detection logic):
·
EGR actuator output current 7 A or higher is detected. ·
ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected. |
·
Open or short in EGR actuator circuit ·
Electric EGR control valve assembly ·
ECM |
Comes on | DTC stored | SAE Code: P0490 |
| DTC No. | Data List |
|---|---|
| P040318
P040319 |
·
Actual EGR Valve Position No.1 ·
Target EGR Valve Position No.1 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P040318
P040319 |
Idle the engine for 5 seconds or more |
Refer to DTC P040371.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>P040371
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>REMOVAL
| *a | Component without harness connected
(Electric EGR Control Valve Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - 4 | Always | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric EGR control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E33-4 (M+) - E7-6 (EGM+) | Always | Below 1 Ω |
| E33-5 (M-) - E7-7 (EGM-) | Always | Below 1 Ω |
| E33-4 (M+) or E7-6 (EGM+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E33-5 (M-) or E7-7 (EGM-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Idle the engine for 5 seconds or more
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT