The EGR system recirculates exhaust gases. The recirculated gas mingles with the intake air so that the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.
In order to increase EGR circulation efficiency, the ECM adjusts the EGR valve angle and the throttle valve angle.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P040371 | Exhaust Gas Recirculation "A" Actuator Stuck | Either of the following conditions is met (1 trip detection logic):
·
The target and actual positions of the EGR valve are different for 20 seconds or more. ·
While the engine is running, the EGR activation duty exceeds the threshold for 0.5 seconds a certain number of times (40 seconds or more). |
·
EGR valve stuck ·
EGR valve does not move smoothly ·
EGR valve deposit ·
ECM |
Comes on | DTC stored | SAE Code: P042E |
| DTC No. | Data List |
|---|---|
| P040371 | ·
Mass Air Flow Sensor ·
Intake Manifold Absolute Pressure ·
EGR Close Learning Value Bank 1 ·
Target EGR Valve Position No.1 ·
Actual EGR Valve Position No.1 |
Actual EGR valve opening percentage: Fully closed = 0%, fully open = 100%.
If DTC P040371 is stored, the following symptoms may appear:
Stuck closed malfunction
Intake booming noise
Slight combustion noise
Stuck open malfunction
Black smoke
Lack of power
Vibration at engine stop
Misfire
White smoke
Engine stall
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P040371 | After warming up engine and idling for 60 seconds, maintain engine speed at 2500 rpm for 40 seconds, drive vehicle, and perform engine brake deceleration by fully closing accelerator when engine speed is 2000 rpm or more. |
When the target and actual positions of the EGR valve are different, the ECM interprets this as a malfunction of the electric EGR control valve assembly and illuminates the MIL (1 trip detection logic).
If a large amount of carbon deposits exists in the electric EGR control valve assembly, the following parts possibly also have deposits inside: The intake manifold and other parts related to the exhaust gas.
Be sure to carefully examine "Actual EGR Valve Position No.1", "Target EGR Valve Position No.1" and "Mass Air Flow Sensor" in the freeze frame data.
When cleaning the electric EGR control valve assembly or diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P040371 is output | A |
| DTC P040371 and other DTCs are output | B |
If any DTCs other than P040371 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position Bank 1 / Data List / Target EGR Valve Position No.1 and Actual EGR Valve Position No.1.
| Active Test Display |
|---|
| Control the EGR Step Position Bank 1 |
| Data List Display |
|---|
| Target EGR Valve Position No.1 |
| Actual EGR Valve Position No.1 |
When changing the Active Test value consecutively to 1, 30, 60, 90, 60, 30 and 1%, check that Actual EGR Valve Position No.1 smoothly changes to the set opening angle.
The Actual EGR Valve Position No.1 value follows the Target EGR Valve Position No.1 value.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>REMOVAL
Reconnect the electric EGR control valve assembly connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position Bank 1.
| Tester Display |
|---|
| Control the EGR Step Position Bank 1 |
Check if the valve of the electric EGR control valve assembly opens/closes when an Active Test is performed.
The valve opens/closes.
| *1 | Gap |
| *a | OK |
| *b | NG |
Hold the electric EGR control valve assembly up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.
No light passes through (there is no gap between the valve and body).
Light passes through part A shown in the illustration even if the valve is completely closed as there is an opening in the seal ring of the valve. This is not a problem.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.
Remove the deposits if there are many deposits in the electric EGR control valve assembly or the passage of the intake manifold.
Reinstall the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>INSTALLATION
A
B
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>REMOVAL
Before replacing the electric EGR control valve assembly, check the connections of the wire harness and connectors. If there is any abnormality, replace or repair the wire harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>REMOVAL
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
When cleaning the electric EGR control valve, make sure the valve is completely closed.
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
When cleaning the electric EGR control valve, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR valve.
When cleaning the electric EGR control valve assembly, perform the initialization procedure.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION
If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.
Reinstall the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/o EGR Cooler)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
After warming up the engine and idling for 60 seconds, maintain the engine speed at 2500 rpm for 40 seconds, drive the vehicle, and perform engine brake deceleration by fully closing the accelerator when engine speed is 2000 rpm or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTCs are not output again.
| Proceed to |
|---|
| NEXT |
NEXT