Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388653 ECD SYSTEM(w/ EGR Cooler) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  Lack of Power (Turbocharger System)  


CAUTION / NOTICE / HINT

HINT:
·

The diagnosis flowchart is for lack of power due to turbocharger factors.

·

If symptom-specific diagnosis indicates a turbocharger related problem, check using this flowchart.



PROCEDURE

1.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check that no soot or oil adheres to the turbocharger sub-assembly connectors.

A445194E02
1.417,1.385 1.573,1.583 0.156,0.198 10 false A 3.719,1.219 3.875,1.417 0.156,0.198 10 false A 4.646,3.198 4.781,3.375 0.135,0.177 10 true B 3.865,3.802 3.99,4.01 0.125,0.208 10 true B 4.646,4.396 4.771,4.604 0.125,0.208 10 true B 5.323,3.875 5.448,4.083 0.125,0.208 10 true B 4.979,3.781 5.104,3.99 0.125,0.208 10 true A 4.073,2.281 4.198,2.49 0.125,0.208 10 true A

HINT:

If adhering soot or an oil leak exists, air leaking at that position may be the cause of the lack of boost pressure.



Result:
Result Proceed to
No adhering soot or an oil A
Soot adhering around the turbine housing, flange, or exhaust pipe clamp (A in the illustration) B
Oil leak from the contact surface between the compressor housing and bearing housing (B in the illustration) C



A

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (TURBINE SHAFT)

B

5.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (TURBINE SHAFT)
a.

Remove the turbocharger sub-assembly.

·

Check that the turbine shaft rotates smoothly, without catching.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>INSPECTION

·

Check for loose turbine mounting nuts and for axial play in the turbine shaft.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>INSPECTION



HINT:

If the turbine shaft catches or if there is no play or excessive play, it could indicate improper sealing due to seizing or poor sliding because of a deposit build-up.


Result:
Result Proceed to
No turbine shaft malfunction A
Turbine shaft malfunction B



A

3.INSPECT TURBOCHARGER SUB-ASSEMBLY

B

3.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Check for interference between the turbine wheel and the turbine housing.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSPECTION

HINT:

When there is interference between the turbine wheel and turbine housing and the turbine wheel is damaged, check for fragments of the turbine wheel in the exhaust manifold converter sub-assembly.



Result:
Result Proceed to
No damage or interference A
Damage or interference exists B



A

4.INSPECT TURBOCHARGER NOZZLE VANE PLATE

B

4.INSPECT TURBOCHARGER NOZZLE VANE PLATE
a.

Inspect the turbocharger nozzle vane plate.

i.

Remove the e-washer from the turbocharger nozzle vane control actuator.



b.
A348999

Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.


Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.



OK

REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

NG

5.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Check for deformation or cracks in the mounting surfaces on the exhaust manifold converter sub-assembly and the turbocharger sub-assembly.

HINT:

Deformation or cracks on a mounting surface may allow exhaust gas to leak from the damaged position.


Standard:

No deformation or cracks on a mounting surface.


Result:
Result Proceed to
No problem with the mounting surface A
Deformation or cracks on the exhaust manifold converter sub-assembly mounting surface B
Deformation or cracks on the turbocharger sub-assembly mounting surface C




A

6.REPLACE EXHAUST PIPE CLAMP AND GASKET

B

REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

6.REPLACE EXHAUST PIPE CLAMP AND GASKET
a.

Replace the exhaust pipe clamp and the gasket.


Result:
Proceed to
NEXT



NEXT

7.PERFORM SIMULATION TEST
7.PERFORM SIMULATION TEST
a.

Check that the abnormal state has disappeared.


Result:
Proceed to
NEXT



NEXT

END