Refer to DTC P007A11.
Refer to DTC P011011.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P011C62 | Charge Air Cooler Temperature/Intake Air Temperature Bank 1 Signal Compare Failure | After the engine is completely warmed up and then allowed to soak for a long time (10 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 25°C (77°F) or higher (2 trip detection logic). | ·
Open or short in intake air temperature sensor circuit ·
Open or short in intake air temperature sensor (turbo) circuit ·
Intake air temperature sensor (built into mass air flow meter sub-assembly) ·
Intake air temperature sensor (turbo) ·
ECM ·
Engine off timer (P261029) |
Class B1 | DTC stored | SAE Code: P011C |
| DTC No. | Data List |
|---|---|
| P011C62 | ·
Intake Air Temperature ·
Intake Air Temperature B1S1 (Turbo) |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P011C62 | After engine completely warmed up, allow engine to soak for long time (10 hours or more).
Start the engine and idle the engine for 3 minutes or more. |
Refer to DTC P007A11.
Refer to DTC P010012.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P011C62 is output | A |
| DTC P011C62 and other DTCs are output | B |
A
B
Allow the engine to soak for 1 to 2 hours.
It is not necessary to allow the engine to soak if the engine is cold.
The engine cools faster if the hood is opened.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Coolant Temperature.
| Tester Display |
|---|
| Coolant Temperature |
Read the value.
The difference between the displayed value and outside air temperature is below 5°C (41°F).
If the difference between "Coolant Temperature" and the outside air temperature is 5°C (41°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Intake Air Temperature.
| Tester Display |
|---|
| Intake Air Temperature |
Read the value.
The difference between the displayed value and outside air temperature is below 25°C (77°F).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Intake Air Temperature B1S1 (Turbo).
| Tester Display |
|---|
| Intake Air Temperature B1S1 (Turbo) |
Read the value.
The difference between the displayed value and outside air temperature is below 25°C (77°F).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E24-2 (THA) - E5-26 (THIA) | Always | Below 1 Ω |
| E24-1 (E2) - E5-27 (E2) | Always | Below 1 Ω |
| E24-2 (THA) or E5-26 (THIA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Allow the engine to soak for 1 to 2 hours.
It is not necessary to allow the engine to soak if the engine is cold.
The engine cools faster if the hood is opened.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Coolant Temperature.
| Tester Display |
|---|
| Coolant Temperature |
Read the value.
If the difference between "Coolant Temperature" and the outside air temperature is 5°C (41°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Intake Air Temperature and Intake Air Temperature B1S1 (Turbo).
| Tester Display |
|---|
| Intake Air Temperature |
| Intake Air Temperature B1S1 (Turbo) |
Read the value.
The difference between the displayed value and outside air temperature is below 25°C (77°F).
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E20-4 (THA) - E6-28 (THA) | Always | Below 1 Ω |
| E20-2 (E2G) - E6-29 (EVG) | Always | Below 1 Ω |
| E20-4 (THA) or E6-28 (THA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
| Proceed to |
|---|
| NEXT |
NEXT