| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P122900 | Fuel Pump Valve Malfunction | The actual fuel pressure exceeds the target fuel pressure by 5000 kPag or higher for 30 seconds. (1 trip detection logic) | ·
Short in pre-stroke control valve circuit ·
Fuel supply pump assembly ·
Fuel pressure sensor (common rail assembly) ·
ECM |
Class A | DTC stored | SAE Code: P1229 |
| DTC No. | Data List |
|---|---|
| P122900 | ·
Fuel Pressure (High) ·
Target Fuel Pressure (High) |
For more information on the fuel supply pump assembly (pre-stroke control valve) and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>SYSTEM DESCRIPTION).
When DTC P122900 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Powertrain / Engine and Transmission / Data List / Fuel Pressure (High), Target Fuel Pressure (High).
Under a stable condition such as idling after warm up the engine, Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) when normal.
This DTC is stored when the actual fuel pressure in the common rail assembly is higher than the target fuel pressure, even though a signal is not being output from the ECM to operate the pre-stroke control valve.
This DTC indicates that the pre-stroke control valve may be stuck or have a short circuit.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P122900 | Idling for 60 seconds or more |
This DTC is stored when the actual fuel pressure in the common rail assembly is higher than the target fuel pressure, even though a signal is not being output from the ECM to drive the pre-stroke control valve. This DTC indicates that the pre-stroke control valve may be stuck or have a short circuit.
If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the engine switch is turned off.
Refer to DTC P062712.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P122900 and "P019011, P019015, P107A11 and/or P107A15" are output | B |
| Except above | A |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).
| Tester Display |
|---|
| Target Fuel Pressure (High) |
| Fuel Pressure (High) |
Check that the internal fuel pressure of the common rail assembly is within the specification below.
Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) when engine is idling after warm up the engine.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Activate the Pre-stroke Control Valve.
| Tester Display |
|---|
| Activate the Pre-stroke Control Valve |
Perform the Active Test and check that operation sounds can be heard from the pre-stroke control valve.
Perform this procedure with the engine stopped and check the operation sounds from outside the vehicle.
Check in a quiet location with the hood opened, as the operation sound is difficult to hear.
In order to distinguish between the operation sounds of other actuators, check by using the GTS to turn the Active Test open and close several times.
The operation sound is generated when performing the Active Test, and stops when finished.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clean the fuel filter case and replace the fuel filter element assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT
Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Start the engine.
Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and Transmission / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P122900.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, increase the idling time.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the pre-stroke control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E102-1 (+B) - E6-3 (PCV+) | Always | Below 1 Ω |
| E102-2 (PCV) - E6-4 (PCV-) | Always | Below 1 Ω |
| E102-1 (+B) or E6-3 (PCV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E102-2 (PCV) or E6-4 (PCV-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Test the Fuel Leak / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).
| Active Test Display |
|---|
| Test the Fuel Leak |
| Data List Display |
|---|
| Target Fuel Pressure (High) |
| Fuel Pressure (High) |
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.
In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag.
"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.
"Fuel Pressure (High)" is the actual fuel pressure.
| Result | Proceed to |
|---|---|
| The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag. | B |
| Except above | A |
A
B