| *1 | Exhaust Fuel Addition Injector Assembly | *2 | Turbocharger Sub-assembly |
| *3 | DPF Catalytic Converter | *4 | No. 1 Nitrogen Oxides Sensor |
| *5 | Exhaust Gas Temperature Sensor | *6 | No. 2 Exhaust Gas Temperature Sensor |
| *7 | No. 3 Exhaust Gas Temperature Sensor | *8 | ECM |
| *a | Exhaust Gas | - | - |
The exhaust fuel addition injector assembly is mounted on the exhaust manifold, and low pressure fuel is supplied to the exhaust fuel addition injector assembly by the feed pump in the supply pump assembly. The exhaust fuel addition injector assembly adds fuel in response to a control signal from the ECM, in order to perform PM forced regeneration.
During PM forced regeneration, the exhaust fuel addition injector assembly adds fuel to raise the DPF* catalyst temperature.
This injector adds fuel by a control signal from the ECM.
This injector is used for two different controls: PM forced regeneration and PM reduction.
During PM forced regeneration, the injector adds fuel to raise the catalyst temperature.
In the other control, the injector helps the air-fuel ratio become rich. As a result, PM in the exhaust gas will be reduced in response to the rich air-fuel ratio.
*: Diesel Particulate Filter
For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.
If DTC P200C4B, P200E4B and P24284B are present, refer to the diagnostic trouble code (DTC) chart for Diesel Particulate Filter System.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P200C4B | Particulate Filter Over Temperature Bank 1 Over Temperature | The value of "Exhaust Temperature B1S3" is higher than 1000°C (1832°F) for 5 seconds (1 trip detection logic). | Main Trouble Area
·
Open or short in exhaust fuel addition injector assembly ·
Exhaust fuel addition injector assembly ·
Exhaust manifold converter sub-assembly Sub Trouble Area ·
No. 3 exhaust gas temperature sensor ·
No. 1 nitrogen oxides sensor ·
Mass air flow meter sub-assembly ·
Manifold absolute pressure sensor ·
Fuel leaks or blockages in exhaust fuel addition injector assembly ·
Fuel supply pump assembly ·
Injector assembly ·
Blockages or leaks in air intake system ·
Blockages or leaks in exhaust system ·
Blockages or leaks in EGR system ·
ECM Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Class B2 | DTC stored | SAE Code: P200C |
| P200E4B | Catalyst System Over Temperature Bank 1 Over Temperature | The value of "Exhaust Temperature B1S2" is higher than 1000°C (1832°F) for 5 seconds (1 trip detection logic). | Main Trouble Area
·
Open or short in exhaust fuel addition injector assembly ·
Exhaust fuel addition injector assembly ·
Exhaust manifold converter sub-assembly Sub Trouble Area ·
No. 2 exhaust gas temperature sensor ·
No. 1 nitrogen oxides sensor ·
Mass air flow meter sub-assembly ·
Manifold absolute pressure sensor ·
Fuel leaks or blockages in exhaust fuel addition injector assembly ·
Fuel supply pump assembly ·
Injector assembly ·
Blockages or leaks in air intake system ·
Blockages or leaks in exhaust system ·
Blockages or leaks in EGR system ·
ECM Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Class B2 | DTC stored | SAE Code: P200E |
| P24284B | Exhaust Gas Temperature Too High Bank 1 Over Temperature | The value of "Exhaust Temperature B1S1" is higher than 1000°C (1832°F) for 5 seconds (1 trip detection logic). | Main Trouble Area
·
Open or short in exhaust fuel addition injector assembly ·
Exhaust fuel addition injector assembly ·
Exhaust manifold converter sub-assembly Sub Trouble Area ·
Exhaust gas temperature sensor ·
No. 1 nitrogen oxides sensor ·
Mass air flow meter sub-assembly ·
Manifold absolute pressure sensor ·
Fuel leaks or blockages in exhaust fuel addition injector assembly ·
Fuel supply pump assembly ·
Injector assembly ·
Blockages or leaks in air intake system ·
Blockages or leaks in exhaust system ·
Blockages or leaks in EGR system ·
ECM Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Class B2 | DTC stored | SAE Code: P2428 |
Due to fail-safe operation when other DTCs (that involve the engine power limit) are stored, PM forced regeneration may be prohibited.
This DTC or P042000, P20CF00, P244B00 and P246300 may be stored due to the fact that PM forced regeneration is prohibited due to the fail-safe operation of other DTCs.
The air fuel ratio and the exhaust gas temperature can be checked by entering the following menus on the GTS: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / A/F (O2) Lambda B1S1, Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
Malfunctions in the engine itself may affect the DPF system control and cause storage of this DTC. For example, malfunctions in the injector assemblies that cause a large amount of smoke emission: These affect the exhaust fuel addition injector assembly operation. Blockages or leaks in the air intake system, or an EGR system malfunction such as EGR passage blockages: These malfunctions affect the DPF catalyst temperature control. Therefore, the engine condition itself should also be checked, in addition to the exhaust fuel addition injector assembly.
| DTC No. | Data List |
|---|---|
| P200C4B
P200E4B P24284B |
·
Mass Air Flow Sensor ·
Intake Manifold Absolute Pressure ·
Intake Air Temperature B1S1 (Turbo) ·
Target Boost Pressure ·
Atmospheric Pressure ·
Coolant Temperature ·
Engine Speed ·
A/F (O2) Lambda B1S1 ·
Exhaust Fuel Addition F/B Bank 1 ·
Exhaust Temperature B1S1 ·
Exhaust Temperature B1S2 ·
Exhaust Temperature B1S3 ·
Catalyst Differential Pressure Bank 1 ·
Injection Feedback Value #1 to #4 ·
Target Injection Volume |
The ECM monitors DPF catalyst temperature. When the temperature becomes high due to uncombusted fuel, engine oil or thermal degradation to the DPF catalyst, the ECM illuminates the MIL (MIL status: Class B2).
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P200C4B | PM forced regeneration*
*: When P200C4B is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data. |
| P200E4B | PM forced regeneration*
*: When P200E4B is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data. |
| P24284B | PM forced regeneration*
*: When P24284B is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data. |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Record the stored DTC and freeze frame data.
| Proceed to |
|---|
| NEXT |
NEXT
Check the values of "Exhaust Temperature B1S1", "Exhaust Temperature B1S2" and "Exhaust Temperature B1S3" that were saved in Procedure 1.
| Result | Items to be Replaced |
|---|---|
| DTC P24284B is output and the value of "Exhaust Temperature B1S1" is 850°C (1562°F) or higher | Exhaust gas temperature sensor |
| DTC P200E4B is output and the value of "Exhaust Temperature B1S2" is 850°C (1562°F) or higher | No. 2 exhaust gas temperature sensor |
| DTC P200C4B is output and the value of "Exhaust Temperature B1S3" is 850°C (1562°F) or higher | No. 3 exhaust gas temperature sensor |
If DTC P200C4B, P200E4B and/or P24284B is output, the exhaust gas temperature sensors need to be replaced. However, make sure to perform all diagnostic procedures for DTC P200C4B, P200E4B and/or P24284B before replacing the exhaust gas temperature sensors.
If the exhaust gas temperature sensors are subjected to an abnormally high temperature, the internal resistance of the sensor increases. This causes incorrect temperature measurement.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the procedure [A] 10 times [B].
Check for black smoke emission during the procedure [A] and [B].
Black smoke is emitted less than 5 times.
Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Even though it has been determined that the exhaust manifold converter sub-assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for DTC P200C4B, P200E4B and/or P24284B before replacing it.
This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.
| Proceed to |
|---|
| NEXT |
NEXT
Check the fuel injection system.
| Proceed to |
|---|
| NEXT |
NEXT
Check the intake/exhaust system.
| Proceed to |
|---|
| NEXT |
NEXT
Check the after treatment control system.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the following items only when it has been determined necessary based on diagnosis for DTC P200C4B, P200E4B and/or P24284B.
Replace the exhaust manifold converter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL
Perform the initialization procedure for "Catalyst Deterioration Learning Value Clear" and "DPF Deposition Value Clear".
Replace the exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
Replace the No. 2 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
Replace the No. 3 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).
Perform PM forced regeneration.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
PM forced regeneration completes normally.
| Proceed to |
|---|
| NEXT |
NEXT