Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EMISSION CONTROL SYSTEM › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384175 EMISSION CONTROL SYSTEM G

1GD-FTV EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343690

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running.


HINT:

When there is a malfunction which causes the EGR system to remain on, black or white smoke may be emitted from the exhaust pipe.


PROCEDURE

Hide 25800 1.CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY OPERATION (w/ EGR System)

a.

Check that the engine starts and idles.


b.

Stop the engine.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

w/o Exhaust Gas Temperature Sensor for EGR:

i.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position Bank1.


ii.

Check the Data List.

Enter the following menus: Powertrain / Engine / Data List / Target EGR Valve Position No. 1 and Actual EGR Valve Position No. 1.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position Bank 1
Data List Display
Target EGR Valve Position No.1
Actual EGR Valve Position No.1
50004 372 70 381,382
OK:
Control Range Condition Specified Condition
Active Test performed (Set EGR position to 0% → 30% → 60% → 90% → 60% → 30% → 0%) Actual EGR valve opening percentage changes according to Active Test operation


If the result is not as specified, refer to DTC P040371.




f.

w/ Exhaust Gas Temperature Sensor for EGR:

i.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Control the EGR Step Position Bank1.


ii.

Check the Data List.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Target EGR Valve Position No. 1 and Actual EGR Valve Position No. 1.

OK:
Control Range Condition Specified Condition
Active Test performed (Set EGR position to 0% → 30% → 60% → 90% → 60% → 30% → 0%) Actual EGR valve opening percentage changes according to Active Test operation


If the result is not as specified, refer to DTC P040371.

Powertrain > Engine and Transmission > Active Test
Active Test Display
Control the EGR Step Position Bank 1
Data List Display
Target EGR Valve Position No.1
Actual EGR Valve Position No.1
50004 456 1 283,284

If the result is not as specified, refer to DTC P040371.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>P040371



Hide 25630 2.INSPECT NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)

Hide 3.VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil dipstick, filler cap, PCV hose or other components may cause the engine to run improperly.

·

Air suction caused by disconnections, looseness or cracks in the parts of the air induction system between the diesel throttle body and cylinder head will cause engine failure or engine malfunctions.



If the result is not as specified, replace parts as necessary.


Hide 5.PERFORM DPF FORCIBLE REGENERATION PROCEDURE (w/ DPF)

a.

Disconnect the cable from the negative (-) battery terminal or remove the EFI-MAIN fuse for 1 minute or more.

HINT:
·

If the MIL is illuminated, first clear the DTCs using the GTS, and then initialize the value for the amount of particulate matter recorded by the ECM by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN fuse. Otherwise, forced DPF regeneration cannot be performed using the Utility.

·

If the MIL is not illuminated, proceed to the next step, as initialization is not necessary.




b.

Connect the GTS to the DLC3.


c.

Start the engine and warm up it.

HINT:
·

Make sure the engine coolant temperature sensor reaches 70°C (158°F) or higher.

·

Make sure the No. 3 exhaust gas temperature sensor reaches 115°C (239°F) or higher.




d.

for Manual Transmission:

Move the shift lever to N and set the parking brake.


e.

for Automatic Transmission:

Move the shift lever to P and set the parking brake.


f.

Turn the GTS on.


g.

w/o Exhaust Gas Temperature Sensor for EGR:

i.

Enter the following menus: Powertrain / Engine / Utility / PM Regenerate Mode.

Powertrain > Engine > Utility
Tester Display
PM Regenerate Mode
50005 372 4576
A258392E10
5.677,1.646 5.813,1.646 5.813,1.646 6.031,1.5 false 2.646,1.896 2.51,1.896 2.51,1.896 2.26,2.115 false 4.458,2.396 4.323,2.396 4.323,2.396 4.073,2.625 false 0.385,2 0.938,2.177 0.552,0.177 10 false 750 rpm 0.323,1.125 0.927,1.313 0.604,0.188 10 false 2000 rpm 0.323,1.365 0.927,1.531 0.604,0.167 10 false 1200 rpm 0.427,0.135 0.885,0.469 0.458,0.333 10 false Engine Speed 2.688,1.813 4.146,1.99 1.458,0.177 10 false PM Regeneration Start 3.823,1.563 5.646,1.74 1.823,0.177 10 false PM Regeneration Completion 3.365,3.177 5.208,3.333 1.844,0.156 10 false 15 to 40 minutes 6.552,3.354 6.896,3.531 0.344,0.177 10 false Time 4.521,2.323 5.667,2.5 1.146,0.177 10 false PM volume stored 6.115,2.823 6.76,2.979 0.646,0.156 10 false 7 to 9% 0.104,1.552 2.281,1.75 2.177,0.198 10 true (Ambient temperature: 25°C (77°F))

CAUTION:

Before performing the Utility, make sure that there are no combustible materials around the DPF and tailpipe.


HINT:
·

During the Utility, the engine speed increases to 2000 rpm, and then decreases to a speed between 1200 and 1400 rpm which is determined by the intake air temperature. The Utility then continues with the engine running at that speed.

·

The engine speed increases during the Utility and the engine speed returns to idle when the Utility is completed.

·

The time it takes to complete the Utility varies depending on the PM volume stored. However, it usually takes approximately 15 to 40 minutes to complete the Utility.

·

Do not cancel the Utility unless absolutely necessary.

·

If the Utility needs to be canceled, push the DPF switch or depress the accelerator pedal and race the engine or depress the clutch pedal to cancel the process. Even if the Utility is stopped before it finishes, "Complete for DPNR/DPF Status Regeneration(PM)" is displayed on the GTS. If the Utility is canceled, it must be performed again.

·

If the differential pressure value increases too much during the Utility, the fail-safe function activates and the Utility is stopped.

·

It may not be possible to perform the Utility when the ambient temperature is extremely low or the elevation is extremely high. In this case, perform the Utility indoors (with the tailpipe pointed towards the outside) or drive the vehicle at a speed of approximately 60 km/h (37 mph) or more for approximately 15 to 40 minutes to perform regeneration.

·

Depending on various conditions, the Utility may not be completed within 30 minutes. If 60 minutes elapse, the system stops the Utility and illuminates the MIL. If this happens, disconnect the cable from the negative (-) battery terminal or remove the EFI-MAIN fuse for 1 minute or more so that the MIL turns off, and then perform the Utility again.





h.

w/ Exhaust Gas Temperature Sensor for EGR:

i.

Enter the following menus: Powertrain / Engine and Transmission / Utility / PM Regenerate Mode.

Powertrain > Engine and Transmission > Utility
Tester Display
PM Regenerate Mode
50005 456 4576
A258392E10
5.677,1.646 5.813,1.646 5.813,1.646 6.031,1.5 false 2.646,1.896 2.51,1.896 2.51,1.896 2.26,2.115 false 4.458,2.396 4.323,2.396 4.323,2.396 4.073,2.625 false 0.385,2 0.938,2.177 0.552,0.177 10 false 750 rpm 0.323,1.125 0.927,1.313 0.604,0.188 10 false 2000 rpm 0.323,1.365 0.927,1.531 0.604,0.167 10 false 1200 rpm 0.427,0.135 0.885,0.469 0.458,0.333 10 false Engine Speed 2.688,1.813 4.146,1.99 1.458,0.177 10 false PM Regeneration Start 3.823,1.563 5.646,1.74 1.823,0.177 10 false PM Regeneration Completion 3.365,3.177 5.208,3.333 1.844,0.156 10 false 15 to 40 minutes 6.552,3.354 6.896,3.531 0.344,0.177 10 false Time 4.521,2.323 5.667,2.5 1.146,0.177 10 false PM volume stored 6.115,2.823 6.76,2.979 0.646,0.156 10 false 7 to 9% 0.104,1.552 2.281,1.75 2.177,0.198 10 true (Ambient temperature: 25°C (77°F))

CAUTION:

Before performing the Utility, make sure that there are no combustible materials around the DPF and tailpipe.


HINT:
·

During the Utility, the engine speed increases to 2000 rpm, and then decreases to a speed between 1200 and 1400 rpm which is determined by the intake air temperature. The Utility then continues with the engine running at that speed.

·

The engine speed increases during the Utility and the engine speed returns to idle when the Utility is completed.

·

The time it takes to complete the Utility varies depending on the PM volume stored. However, it usually takes approximately 15 to 40 minutes to complete the Utility.

·

Do not cancel the Utility unless absolutely necessary.

·

If the Utility needs to be canceled, push the DPF switch or depress the accelerator pedal and race the engine or depress the clutch pedal to cancel the process. Even if the Utility is stopped before it finishes, "Complete for DPNR/DPF Status Regeneration(PM)" is displayed on the GTS. If the Utility is canceled, it must be performed again.

·

If the differential pressure value increases too much during the Utility, the fail-safe function activates and the Utility is stopped.

·

It may not be possible to perform the Utility when the ambient temperature is extremely low or the elevation is extremely high. In this case, perform the Utility indoors (with the tailpipe pointed towards the outside) or drive the vehicle at a speed of approximately 60 km/h (37 mph) or more for approximately 15 to 40 minutes to perform regeneration.

·

Depending on various conditions, the Utility may not be completed within 30 minutes. If 60 minutes elapse, the system stops the Utility and illuminates the MIL. If this happens, disconnect the cable from the negative (-) battery terminal or remove the EFI-MAIN fuse for 1 minute or more so that the MIL turns off, and then perform the Utility again.