The urea pump has a level sensor that detects the position of the surface of the fluid inside the urea tank in order to measure the remaining quantity of urea solution.
When the remaining quantity of urea solution falls below a fixed value, a warning is displayed on the combination meter.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P203A12 | Reductant Level Sensor Circuit High Circuit Short to Battery | An open or short in the level sensor (urea pump) circuit for 3 seconds or more (1 trip detection logic). | ·
Open or short in the level sensor circuit ·
Level sensor (urea pump) ·
ECU |
Class A | DTC stored | SAE Code: P203D |
| P203A14 | Reductant Level Sensor Circuit Low Circuit Short to Ground or Open | An open or short in the level sensor (urea pump) circuit for 3 seconds or more (1 trip detection logic). | ·
Open or short in the level sensor circuit ·
Level sensor (urea pump) ·
ECU |
Class A | DTC stored | SAE Code: P203C |
| DTC No. | Data List |
|---|---|
| P203A12
P203A14 |
Reductant Level |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P203A12
P203A14 |
Engine switch on (IG) for 3 seconds or more |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the level sensor (urea pump).
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the urea pump connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| x4-13 (VLV1) - N37-60 (VCLU) | Always | Below 1 Ω |
| x4-14 (LV1) - N37-59 (LVU) | Always | Below 1 Ω |
| x4-6 (ELV1) - N37-58 (ELU) | Always | Below 1 Ω |
| x4-13 (VLV1) or N37-60 (VCLU) - Body ground and other terminals | Always | 10 kΩ or higher |
| x4-14 (LV1) or N37-59 (LVU) - Body ground and other terminals | Always | 10 kΩ or higher |
| x4-6 (ELV1) or N37-58 (ELU) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and wait for 3 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P203A12 or P203A14 is output | A |
| No DTC is output | B |
A
B
Replace the urea pump control ECU.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and wait for 3 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the urea pump.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT