This is the repair procedure for the accelerator pedal sensor assembly.
This electrical throttle system does not use a throttle cable.
This accelerator pedal position sensor is a non-contact type.
The accelerator pedal position sensor is mounted on the accelerator pedal sensor assembly and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal position sensor.
In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0.5 V and 4.8 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P212012 | Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery | VPA is 4.8 V or higher for 2 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in EPA circuit ·
Short in VPA circuit ·
ECM |
Class B2 | DTC stored | SAE Code: P2123 |
| P212014 | Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open | VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in VCPA circuit ·
VPA circuit open or shorted to ground ·
ECM |
Class B2 | DTC stored | SAE Code: P2122 |
| P21201C | Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range | Difference between VPA and VPA2 is greater than or equal to the specified value for 2 seconds (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
ECM |
Class B2 | DTC stored | SAE Code: P2121 |
| P21201F | Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent | VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Accelerator pedal sensor assembly circuit ·
ECM |
Class B2 | DTC stored | SAE Code: P2120 |
| P212099 | Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit | Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V (learned value of accelerator off position) (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
ECM |
Class B2 | DTC stored | SAE Code: P2121 |
| P212512 | Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery | Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher. (b) VPA is between 0.4 V and 3.45 V. |
·
Accelerator pedal sensor assembly ·
Open in EPA2 circuit ·
Short in VPA2 circuit ·
ECM |
Class B2 | DTC stored | SAE Code: P2128 |
| P212514 | Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open | VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Open in VCP2 circuit ·
VPA2 circuit open or shorted to ground ·
ECM |
Class B2 | DTC stored | SAE Code: P2127 |
| P21251F | Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent | VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Accelerator pedal sensor assembly circuit ·
ECM |
Class B2 | DTC stored | SAE Code: P2125 |
| P21382B | Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled | Difference between VPA and VPA2 is 0.02 V or less for 2.0 seconds or more (1 trip detection logic) | ·
Accelerator pedal sensor assembly ·
Accelerator pedal sensor assembly circuit ·
ECM |
Class B2 | DTC stored | SAE Code: P2138 |
| DTC No. | Data List |
|---|---|
| P212012
P212014 P21201C P21201F P212099 P212512 P212514 P21251F P21382B |
·
Accel Position ·
Accelerator Position Sensor No.1 Voltage % ·
Accelerator Position Sensor No.2 Voltage % |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P212012
P212014 P21201C P21201F P212099 P212512 P212514 P21251F P21382B |
Engine switch on (IG)
·
Accelerator pedal fully released for 3 seconds ·
Accelerator pedal depressed partway for 3 seconds ·
Accelerator pedal fully depressed for 3 seconds |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Primary / Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %.
| Tester Display |
|---|
| Accelerator Position Sensor No.1 Voltage % |
| Accelerator Position Sensor No.2 Voltage % |
| *1 | Accelerator Pedal Sensor Assembly |
| *a | Depressed |
| *b | Released |
Read the values.
| Accelerator Pedal | Accelerator Position Sensor No.1 Voltage % | Accelerator Position Sensor No.2 Voltage % |
|---|---|---|
| Released | 10 to 22% | 24 to 40% |
| Depressed | 52 to 90% | 68 to 99% |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A2-29 (VCPA) - A2-22 (EPA) | Engine switch on (IG) | 4.5 to 5.5 V |
| A2-30 (VCP2) - A2-25 (EPA2) | Engine switch on (IG) | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A2-28 (VPA) - A2-22 (EPA) | Engine switch on (IG), accelerator pedal fully released | 0.5 to 1.1 V |
| Engine switch on (IG), accelerator pedal fully depressed | 3.0 to 4.6 V | |
| A2-31 (VPA2) - A2-25 (EPA2) | Engine switch on (IG), accelerator pedal fully released | 0.9 to 2.3 V |
| Engine switch on (IG), accelerator pedal fully depressed | 3.4 to 5.0 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal sensor assembly connector.
| *a | Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M3-4 (VCPA) - M3-5 (EPA) | Engine switch on (IG) | 4.5 to 5.5 V |
| M3-1 (VCP2) - M3-2 (EPA2) | Engine switch on (IG) | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M3-6 (VPA) - A2-28 (VPA) | Always | Below 1 Ω |
| M3-5 (EPA) - A2-22 (EPA) | Always | Below 1 Ω |
| M3-3 (VPA2) - A2-31 (VPA2) | Always | Below 1 Ω |
| M3-2 (EPA2) - A2-25 (EPA2) | Always | Below 1 Ω |
| M3-6 (VPA) or A2-28 (VPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| M3-5 (EPA) or A2-22 (EPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| M3-3 (VPA2) or A2-31 (VPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| M3-2 (EPA2) or A2-25 (EPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal sensor assembly connector.
| *a | Component with harness connected
(ECM) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A2-29 (VCPA) - A2-28 (VPA) | Engine switch off | No short or no open circuit |
| A2-28 (VPA) - A2-22 (EPA) | Engine switch off | No short or no open circuit |
| A2-30 (VCP2) - A2-31 (VPA2) | Engine switch off | No short or no open circuit |
| A2-31 (VPA2) - A2-25 (EPA2) | Engine switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the engine switch off and leave the vehicle for 30 seconds.
Turn the engine switch on (IG).
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT