Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P219519  A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Above Threshold  P219618  A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P219519 A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Above Threshold While the fuel-cut operation is performed (during vehicle deceleration), the No. 1 nitrogen oxides sensor current meets or exceeds the threshold* for 3 seconds (2 trip detection logic).
*: Threshold value changes from 1.98 to 2.41 mA depending on atmospheric conditions
·

No. 1 nitrogen oxides sensor

·

ECM


Class B1 DTC stored SAE Code: P2195
P219618 A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Below Threshold While the fuel-cut operation is performed (during vehicle deceleration), the No. 1 nitrogen oxides sensor current is less than -12.4 mA for 3 seconds (2 trip detection logic).
·

No. 1 nitrogen oxides sensor

·

ECM


Class B1 DTC stored SAE Code: P2196

Related Data List
DTC No. Data List
P219519
P219618
A/F (O2) Lambda B1S1

MONITOR DESCRIPTION

The ECM monitors the No. 1 nitrogen oxides sensor current during fuel-cut and detects any abnormal current values.

If the No. 1 nitrogen oxides sensor current meets or exceeds the threshold* for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the No. 1 nitrogen oxides sensor and stores DTC P219519 (stuck on lean side). If the No. 1 nitrogen oxides sensor current is less than -12.4 mA for more than 3 seconds of cumulative time, the ECM stores DTC P219618 (stuck on rich side).

*: Threshold value changes from 1.98 to 2.41 mA depending on atmospheric conditions

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P219519
P219618
After the engine is fully warmed up, the accelerator pedal is released for 7 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph).

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL

HINT:

Perform "A/F Sensor Learning Value Clear" after replacing the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Turn the engine switch off and wait for 30 seconds or more.


f.

Start the engine and warm it up.


g.

After the engine is fully warmed up, the release the accelerator pedal and wait for 7 seconds and more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph).

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

j.

Read the DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and Transmission / Utility / All Readiness.

Powertrain > Engine and Transmission > Utility
Tester Display
All Readiness
50005 456 20

ii.

Input DTC P219519 or P219618.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P219519 or P219618 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE, the release the accelerator pedal and wait for 7 seconds and more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph) again.





A

END

B