Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P246E11  Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Ground  P246E15  Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

A443538E01
2.26,2.083 2.51,2.469 2.51,2.469 5.104,2.469 true 3.75,2.073 4,2.458 true 4.208,0.698 4.688,0.698 4.688,0.698 5.073,1.448 true 4.25,2.083 4.5,2.469 true 0.125,1.615 1.052,1.865 0.927,0.25 10 false Exhaust Gas 1.75,0.604 4.302,0.865 2.552,0.26 10 false No. 4 Exhaust Gas Temperature Sensor 6.302,0.417 6.802,0.625 0.5,0.208 10 false ECM 5.198,2.396 6.219,2.604 1.021,0.208 10 false SCR Catalyst

The No. 4 exhaust gas temperature sensor is installed after the SCR catalyst to detect the exhaust gas temperature. A thermistor built into the No. 4 exhaust gas temperature sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value. The No. 4 exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage is applied to the No. 4 exhaust gas temperature sensor from terminal THSO via resistor R.

Resistor R and the No. 4 exhaust gas temperature sensor are connected in series. When the resistance value of the No. 4 exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminal THSO also changes. The No. 4 exhaust gas temperature sensor monitors the temperature downstream of the SCR catalyst.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P246E11 Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Ground No. 4 exhaust gas temperature sensor output voltage is below 0.11 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

Open or short in No. 4 exhaust gas temperature sensor circuit

·

No. 4 exhaust gas temperature sensor

·

ECM


Class B1 DTC stored SAE Code: P2470
P246E15 Exhaust Gas Temperature Sensor 4 Bank 1 Circuit Short to Battery or Open No. 4 exhaust gas temperature sensor output voltage is higher than 4.89 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

After starting the engine, 17 minutes or more elapses

·

Engine is running

·

Coolant temperature is 75°C (167°F) or higher


·

Open or short in No. 4 exhaust gas temperature sensor circuit

·

No. 4 exhaust gas temperature sensor

·

ECM


Class B1 DTC stored SAE Code: P2471

Related Data List
DTC No. Data List
P246E11
P246E15
Exhaust Temperature B1S4

HINT:

When DTC P246E11 and P246E15 is output, check the downstream exhaust gas temperature indicated by "Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S4" using the GTS.

Reference:
Condition Exhaust Temperature B1S4 No. 4 Exhaust Gas Temperature Sensor Condition
Idling with warm engine Constant at between 50 and 700°C (122 and 1292°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the No. 4 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.11 V and 4.89 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL (MIL status: Class B1).

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P246E11 Engine switch on (IG) for 3 seconds or more
P246E15 Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 17 minutes to elapse after starting the engine.

WIRING DIAGRAM

A356866E06
2.302,1.354 2.917,1.552 0.615,0.198 10 false THSO 3.125,1.344 3.385,1.604 0.26,0.26 10 false E2 2.115,1.573 2.271,1.771 0.156,0.198 10 false 2 3.417,1.552 3.573,1.75 0.156,0.198 10 false 1 1.917,1.813 2.229,2.01 0.313,0.198 10 false Y2 1.927,1.99 4.469,2.396 2.542,0.406 10 false No. 4 Exhaust Gas Temperature Sensor 5.938,1.927 6.552,2.125 0.615,0.198 10 false E5 5.948,2.094 6.406,2.292 0.458,0.198 10 false ECM 5.552,0.583 6.167,0.781 0.615,0.198 10 false THSO 5.552,1.458 6.167,1.656 0.615,0.198 10 false E2 5.271,0.49 5.583,0.688 0.313,0.198 10 false 24 5.281,1.344 5.594,1.542 0.313,0.198 10 false 27

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (EXHAUST TEMPERATURE B1S4)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S4.

Powertrain > Engine and Transmission > Data List
Tester Display
Exhaust Temperature B1S4
50003 456 342

d.

Read the value.

Standard:

Same as the actual No. 4 exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling with warm engine), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Temperature Displayed Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) B
OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warmup), and varies after maintaining an engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C


HINT:
·

If there is a short circuit, the GTS will indicate 0°C (32°F).

·

If there is an open circuit, the GTS will indicate 1000°C (1832°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A449026C01
1.479,2.719 1.927,3.052 0.448,0.333 1.281,4.229 1.615,3.573 true 2.323,4.219 1.792,3.604 true 0.563,2.76 0.875,2.958 0.313,0.198 10 false *a 0.688,1.802 1,2 0.313,0.198 10 false *1 2.583,1.771 2.896,1.969 0.313,0.198 10 false *2 1.573,0.667 1.99,0.854 0.417,0.188 10 false THSO 1.635,1.375 2.083,1.573 0.448,0.198 10 false E2 1.583,2.813 2.031,3.031 0.448,0.219 10 false Y2 1.167,4.26 1.458,4.438 0.292,0.177 10 false E2 2.229,4.26 2.625,4.458 0.396,0.198 10 false THSO
*1 No. 4 Exhaust Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to No. 4 Exhaust Gas Temperature Sensor)


Disconnect the No. 4 exhaust gas temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THSO) of the No. 4 exhaust gas temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S4.

Powertrain > Engine and Transmission > Data List
Tester Display
Exhaust Temperature B1S4
50003 456 342

f.

Read the value.

Standard:

1000°C (1832°F)



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
3.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the No. 4 exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y2-2 (THSO) - E5-24 (THSO) Always Below 1 Ω
Y2-1 (E2) - E5-27 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Turn the engine switch off for 30 seconds or more.


f.

Start the engine and turn the GTS on.


g.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 17 minutes to elapse after starting the engine.


h.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

i.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A178587C05
0.792,1.594 1.104,1.792 0.313,0.198 10 false *1 2.698,1.677 3.01,1.875 0.313,0.198 10 false *2
*1 No. 4 Exhaust Gas Temperature Sensor
*2 ECM


Disconnect the No. 4 exhaust gas temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S4.

Powertrain > Engine and Transmission > Data List
Tester Display
Exhaust Temperature B1S4
50003 456 342

e.

Read the value.

Standard:

0°C (32°F)



Result:
Proceed to
OK
NG



OK

8.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

9.CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
8.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the No. 4 exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y2-2 (THSO) or E5-24 (THSO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Turn the engine switch off for 30 seconds or more.


f.

Turn the engine switch on (IG) for 3 seconds or more.


g.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

h.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Turn the engine switch off for 30 seconds or more.


f.

Start the engine and turn the GTS on.


g.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 17 minutes to elapse after starting the engine.


h.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

i.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END