Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), battery power is supplied to the IGSW terminal of the ECM and MREL is operated.

As a result, the EFI MAIN Relay contact closes and power is supplied to the +B, +B2 and +B3 terminals of the ECM.

WIRING DIAGRAM

A449024E01
6.208,0.729 6.635,0.917 0.427,0.188 10 false IGSW 5.906,0.729 6.219,0.885 0.313,0.156 10 false A2 6.219,3.188 6.458,3.344 0.24,0.156 10 false +B 6.229,3.656 6.521,3.823 0.292,0.167 10 false +B2 6.219,4.219 6.542,4.385 0.323,0.167 10 false +B3 5.896,3.188 6.208,3.344 0.313,0.156 10 false N2 5.896,3.667 6.208,3.823 0.313,0.156 10 false N2 5.906,4.229 6.219,4.385 0.313,0.156 10 false N2 6.219,4.74 6.635,4.917 0.417,0.177 10 false MREL 5.906,0.531 6.115,0.698 0.208,0.167 10 false 18 5.896,4.74 6.208,4.896 0.313,0.156 10 false N2 5.896,5.49 6.208,5.646 0.313,0.156 10 false A2 6.229,5.49 6.479,5.667 0.25,0.177 10 false E1 5.948,2.979 6.135,3.146 0.188,0.167 10 false 4 5.938,3.479 6.125,3.646 0.188,0.167 10 false 3 5.938,4.021 6.125,4.188 0.188,0.167 10 false 2 5.906,4.542 6.094,4.708 0.188,0.167 10 false 14 5.927,5.302 6.115,5.469 0.188,0.167 10 false 5 6.448,6.198 6.802,6.385 0.354,0.188 10 false ECM 4.406,0.719 4.667,0.875 0.26,0.156 10 false 1D 4.448,1.188 4.635,1.354 0.188,0.167 10 false 2 4.406,1.396 4.667,1.552 0.26,0.156 10 false 1D 4.458,0.521 4.646,0.688 0.188,0.167 10 false 1 5.042,0.906 5.708,1.104 0.667,0.198 10 false IG2 NO. 1 3.594,1.688 4.302,1.896 0.708,0.208 10 false IG2 MAIN 2.156,1.177 2.344,1.344 0.188,0.167 10 false 4 2.667,0.875 3.354,1.094 0.688,0.219 10 false IG2-MAIN 2.552,3.406 5.594,3.865 3.042,0.458 10 false Certification ECU (Smart Key ECU Assembly) 2.583,3.25 2.969,3.448 0.385,0.198 10 false N156 0.688,4.969 1.656,5.167 0.969,0.198 10 false FL MAIN 3.948,5.052 4.635,5.26 0.688,0.208 10 false EFI MAIN 1.24,4.396 1.99,4.604 0.75,0.208 10 false EFI-MAIN 0.771,5.938 1.74,6.135 0.969,0.198 10 false Battery 2.115,1.375 2.375,1.531 0.26,0.156 10 false 1E 2.156,0.719 2.417,0.875 0.26,0.156 10 false A 2.146,0.51 2.333,0.677 0.188,0.167 10 false 1 2.656,1.917 4.313,2.146 1.656,0.229 10 false No. 1 Integration Relay 3.802,4.104 3.99,4.271 0.188,0.167 10 false 3 4.635,4.104 4.823,4.271 0.188,0.167 10 false 5 3.813,4.625 4,4.792 0.188,0.167 10 false 1 4.615,4.604 4.802,4.771 0.188,0.167 10 false 2 3.75,2.792 4.135,2.99 0.385,0.198 10 false IG1D 4.167,2.677 4.552,2.875 0.385,0.198 10 false 17

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT ECM (+B VOLTAGE)
a.
A348466C55
2.833,0.365 3.208,0.615 0.375,0.25 2.281,0.354 2.656,0.604 0.375,0.25 2.188,1.583 2.479,1 true 2.49,1.771 2.552,1 true 2.771,1.552 2.604,1 true 3.135,1.771 2.969,1 true 2.938,0.406 3.281,0.615 0.344,0.208 10 false A2 2.396,0.406 2.74,0.615 0.344,0.208 10 false N2 2,1.594 2.469,1.813 0.469,0.219 10 false 4 (+B) 2.271,1.813 2.792,2.021 0.521,0.208 10 false 3 (+B2) 2.573,1.583 3.094,1.792 0.521,0.208 10 false 2 (+B3) 2.979,1.813 3.427,2.042 0.448,0.229 10 false 5 (E1) 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Component with harness connected
(ECM)


Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N2-4 (+B) - A2-5 (E1) Engine switch on (IG) 11 to 14 V
N2-3 (+B2) - A2-5 (E1) Engine switch on (IG) 11 to 14 V
N2-2 (+B3) - A2-5 (E1) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-5 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (IGSW VOLTAGE)
a.
A348466C56
2.813,0.344 3.219,0.583 0.406,0.24 3.063,1.854 3.219,1.125 true 2.677,1.667 2.906,1 true 2.938,0.385 3.26,0.573 0.323,0.188 10 false A2 2.74,1.896 3.427,2.083 0.688,0.188 10 false 18 (IGSW) 2.521,1.719 3.208,1.906 0.688,0.188 10 false 5 (E1) 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a
*a Component with harness connected
(ECM)


Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A2-18 (IGSW) - A2-5 (E1) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT EFI MAIN RELAY

NG

7.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY - BODY GROUND)
4.INSPECT EFI MAIN RELAY

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - EFI MAIN RELAY)

NG

REPLACE EFI MAIN RELAY

5.CHECK HARNESS AND CONNECTOR (ECM - EFI MAIN RELAY)
a.

Disconnect the ECM connector.


b.

Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-14 (MREL) - EFI MAIN relay terminal 2 Always Below 1 Ω
N2-4 (+B) - EFI MAIN relay terminal 5 Always Below 1 Ω
N2-3 (+B2) - EFI MAIN relay terminal 5 Always Below 1 Ω
N2-2 (+B3) - EFI MAIN relay terminal 5 Always Below 1 Ω
N2-14 (MREL) or EFI MAIN relay terminal 2 - Body ground and other terminals Always 10 kΩ or higher
N2-4 (+B) or EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher
N2-3 (+B2) or EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher
N2-2 (+B3) or EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI MAIN RELAY)
A444449C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 0.49,0.25 0.802,0.406 0.313,0.156 10 false *a
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*a EFI MAIN relay holder


a.

Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
EFI MAIN relay terminal 3 - Body ground Always 11 to 14 V
EFI MAIN relay terminal 1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI MAIN RELAY)

7.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-18 (IGSW) - 1D-1 Always Below 1 Ω
1E-4 - Body ground Always Below 1 Ω
A2-18 (IGSW) or 1D-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 1 INTEGRATION RELAY (IG2 MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT NO. 1 INTEGRATION RELAY (IG2 MAIN RELAY)
a.

Inspect the No. 1 integration relay (IG2 MAIN relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
A443534C01
0.573,2.698 0.875,2.927 0.302,0.229 0.677,2.729 0.833,2.927 0.156,0.198 10 false A 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a
*a No. 1 Engine Room Relay Block and Junction Block Assembly without No. 1 Integration Relay


a.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N156-17 (IG1D) - 1D-2 Always Below 1 Ω
1E-4 - Body ground Always Below 1 Ω
N156-17 (IG1D) or 1D-2 Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR