Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P225F2A  NOx Sensor Performance - Signal Biased/Stuck Low Bank 1 Sensor 2 Signal Stuck In Range  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P225F2A NOx Sensor Performance - Signal Biased/Stuck Low Bank 1 Sensor 2 Signal Stuck In Range The A/F output value of the No. 2 nitrogen oxides sensor exceeds the threshold during high load driving or during fuel cut.
(2 trip detection logic)
No. 2 nitrogen oxides sensor Class B1 DTC Stored SAE Code: P225F

Related Data List
DTC No. Data List
P225F2A
·

NOx Sensor NOx Active Status (SCU)

·

NOx Sensor A/F Active Status (SCU)



MONITOR DESCRIPTION

The ECU compares the NOx output value of the No. 1 nitrogen oxides sensor and No. 2 nitrogen oxides sensor, and monitors the NOx purification rate.

In a normal system, hardly any NOx is included in exhaust gas near the No. 2 nitrogen oxides sensor, after passing through the SCR catalyst.

During a high load or during fuel cut, the A/F output of the No. 2 nitrogen oxides sensor is checked to determine that the No. 2 nitrogen oxides sensor is not stuck.

If the A/F output value is stuck at a higher value than the threshold when in a rich state during a high load or stuck at a lower value than the threshold when in a lean state during fuel cut, it determines that the NOx output of the No. 2 nitrogen oxides sensor is also stuck and outputs P225F2A.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P225F2A Warm up the engine. With the No. 2 nitrogen oxides sensor active, drive the vehicle at a constant speed of 70 km/h (43.8 mph) in 4th gear for 5 minutes, and then release the accelerator pedal for 10 seconds or more to decelerate.
HINT:

Activation of the No. 2 nitrogen oxides sensor can be checked by confirming whether the "NOx Sensor NOx Active Status (SCU)" and "NOx Sensor A/F Active Status (SCU)" Data List items are "ON".



CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.REPLACE NO. 2 NITROGEN OXIDES SENSOR
a.

Replace the No. 2 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Turn the engine switch off and wait for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Start the engine and warm it up.


g.

Enter the following menus: Powertrain / Engine and Transmission / Data List / NOx Sensor NOx Active Status (SCU) and NOx Sensor A/F Active Status (SCU).

Powertrain > Engine and Transmission > Data List
Tester Display
NOx Sensor NOx Active Status (SCU)
NOx Sensor A/F Active Status (SCU)
50003 456 159,160

h.

With the No. 2 nitrogen oxides sensor active, drive the vehicle at a constant speed of 70 km/h (43.8 mph) in 4th gear for 5 minutes, and then release the accelerator pedal for 10 seconds or more to decelerate.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Activation of the No. 2 nitrogen oxides sensor can be checked by confirming whether the "NOx Sensor NOx Active Status (SCU)" and "NOx Sensor A/F Active Status (SCU)" Data List items are "ON".



i.

Turn the GTS on.


j.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

k.

Read the DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and Transmission / Utility / All Readiness.

Powertrain > Engine and Transmission > Utility
Tester Display
All Readiness
50005 456 20

ii.

Input DTC P225F2A.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P225F2A is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE, perform the following procedure again: With the No. 2 nitrogen oxides sensor active, drive the vehicle at a constant speed of 70 km/h (43.8 mph) in 4th gear for 5 minutes, and then release the accelerator pedal for 10 seconds or more to decelerate.





A

END

B