Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P248E12  Exhaust Gas Recirculation Cooler Bypass Control Circuit High Bank 2 Circuit Short to Battery  P248E14  Exhaust Gas Recirculation Cooler Bypass Control Circuit Low Bank 2 Circuit Short to Ground or Open  


DESCRIPTION

The vacuum switching valve assembly (for No. 2 EGR Bypass Valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P248E12 Exhaust Gas Recirculation Cooler Bypass Control Circuit High Bank 2 Circuit Short to Battery Open or short in the vacuum switching valve assembly (for No. 2 EGR Bypass Valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve assembly (for No. 2 EGR Bypass Valve) circuit

·

Vacuum switching valve assembly (for No. 2 EGR Bypass Valve)

·

ECM


Class B2 DTC stored SAE Code: P2491
P248E14 Exhaust Gas Recirculation Cooler Bypass Control Circuit Low Bank 2 Circuit Short to Ground or Open Open or short in the vacuum switching valve assembly (for No. 2 EGR Bypass Valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve assembly (for No. 2 EGR Bypass Valve) circuit

·

Vacuum switching valve assembly (for No. 2 EGR Bypass Valve)

·

ECM


Class B2 DTC stored SAE Code: P2490

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P248E12
P248E14
Engine switch on (IG) for 3 seconds or more

WIRING DIAGRAM

A444447E03
6.177,2.854 6.792,3.052 0.615,0.198 10 false MREL 5.865,2.969 6.479,3.167 0.615,0.198 10 false N2 5.865,0.51 6.479,0.708 0.615,0.198 10 false 12 4.646,2.729 5.5,2.927 0.854,0.198 10 false EFI NO. 2 3.531,3.313 4.385,3.51 0.854,0.198 10 false EFI MAIN 1.167,2.76 2.021,2.958 0.854,0.198 10 false EFI-MAIN 1.219,2.438 1.396,2.656 0.177,0.219 11 false 1 1.542,2.438 1.719,2.656 0.177,0.219 11 false 2 3.344,2.438 3.521,2.656 0.177,0.219 11 false 3 3.344,2.865 3.521,3.083 0.177,0.219 11 false 1 4.115,2.865 4.292,3.083 0.177,0.219 11 false 2 4.115,2.438 4.292,2.656 0.177,0.219 11 false 5 4.677,2.438 4.854,2.656 0.177,0.219 11 false 1 5.063,2.438 5.24,2.656 0.177,0.219 11 false 2 5.875,0.719 6.49,0.917 0.615,0.198 10 false E8 2.844,1.094 3.458,1.292 0.615,0.198 10 false E108 5.865,2.75 6.479,2.948 0.615,0.198 10 false 14 0.76,3.635 1.615,3.833 0.854,0.198 10 false Battery 0.552,2.979 1.406,3.177 0.854,0.198 10 false FL MAIN 6.365,3.729 7.156,4.021 0.792,0.292 10 false ECM 2.844,1.219 5.031,1.667 2.188,0.448 10 false Vacuum Switching Valve Assembly (for No. 2 EGR Bypass Valve) 2.958,0.708 3.813,0.906 0.854,0.198 10 false +B 4.125,0.719 4.979,0.917 0.854,0.198 10 false ECB2 4.646,0.604 5.26,0.802 0.615,0.198 10 false 2 2.729,0.583 3.344,0.781 0.615,0.198 10 false 1 6.177,0.708 7.031,0.906 0.854,0.198 10 false ECB2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR NO. 2 EGR BYPASS VALVE)
a.

Inspect the vacuum switching valve assembly (for NO. 2 EGR Bypass Valve).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK VACUUM SWITCHING VALVE ASSEMBLY (FOR NO. 2 EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)

NG

7.REPLACE VACUUM CONTROL VALVE SET
2.CHECK VACUUM SWITCHING VALVE ASSEMBLY (FOR NO. 2 EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)
a.

Disconnect the vacuum switching valve assembly (for NO. 2 EGR Bypass Valve) connector.


b.
A348992C14
1.469,1.042 1.917,1.365 0.448,0.323 1.104,2.906 1.521,2.49 true 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 1.542,1.125 1.906,1.344 0.365,0.219 10 false E108 0.896,2.927 1.26,3.146 0.365,0.219 10 false +B
*a Front view of wire harness connector
(to Vacuum Switching Valve Assembly (for No. 2 EGR Bypass Valve))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E108-1 (+B) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR NO. 2 EGR BYPASS VALVE) - ECM)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR NO. 2 EGR BYPASS VALVE) - ECM)
a.

Disconnect the vacuum switching valve assembly (for No. 2 EGR Bypass Valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E108-2 (ECB2) - E8-12 (ECB2) Always Below 1 Ω
E108-2 (ECB2) or E8-12 (ECB2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the vacuum switching valve assembly (for No. 2 EGR Bypass Valve) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve assembly (for No. 2 EGR Bypass Valve) and No. 1 engine room relay block and junction block assembly.



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

c.

Turn the engine switch on (IG) for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE VACUUM CONTROL VALVE SET

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED