Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P026A00  Charge Air Cooler Efficiency Below Threshold  


DESCRIPTION

The ECU compares the intake air temperature before and after passing through the intercooler, and stores P026A00 if it determines that the cooling efficiency of the intercooler has decreased.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P026A00 Charge Air Cooler Efficiency Below Threshold The intercooler efficiency calculated from the intake air temperature before and after passing through the intercooler when driving has decreased to the specified value or lower (2 trip detection logic).
·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

Intake air temperature sensor (built into mass air flow meter sub-assembly) circuit

·

Intake air temperature sensor (turbo)

·

Intake air temperature sensor (turbo) circuit

·

Intake system air leak

·

Intercooler fin deformation or clogging

·

Intercooler

·

ECM


Class B1 DTC stored SAE Code: P026A

Related Data List
DTC No. Data List
P026A00
·

Intake Air Temperature

·

Intake Air Temperature B1S1 (Turbo)



MONITOR DESCRIPTION

The ECU compares the intake air temperature before and after passing through the intercooler when driving, and stores P026A00 if it determines that the cooling efficiency of the intercooler has decreased.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P026A00 Start the engine, drive the vehicle at 70 km/h (43.8 mph) for 10 minutes and check that Intake Air Temperature B1S1 (Turbo) is not higher than Intake Air Temperature by 12°C or more.
(Must not be during PM forced regeneration.)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P026A00)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 456
Result:
Result Proceed to
DTC P026A00 is output A
DTC P026A00 and other DTCs are output B


HINT:

If any DTCs other than P026A00 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (INTAKE AIR TEMPERATURE AND INTAKE AIR TEMPERATURE B1S1 (TURBO))

B

2.READ VALUE USING GTS (INTAKE AIR TEMPERATURE AND INTAKE AIR TEMPERATURE B1S1 (TURBO))
a.

Remove the mass air flow meter sub-assembly.

HINT:

Leave the connector connected.



b.

Remove the intake air temperature sensor (turbo).

HINT:

Leave the connector connected.



c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Intake Air Temperature and Intake Air Temperature B1S1 (Turbo).

Powertrain > Engine and Transmission > Data List
Tester Display
Intake Air Temperature
Intake Air Temperature B1S1 (Turbo)
50003 456 241,331

f.

Read the value displayed on the GTS.

Result:
Result Proceed to
Other than the following. A
Difference between Intake Air Temperature in the Data List and actual outside air temperature value is 10°C (18°F) or more. B
Difference between Intake Air Temperature B1S1 (Turbo) in the Data List and actual outside air temperature value is 10°C (18°F) or more. C




A

3.CHECK INTERCOOLER

B

5.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)

C

8.INSPECT INTAKE AIR TEMPERATURE SENSOR (TURBO)
3.CHECK INTERCOOLER
a.

Check that the intake system pipes are not detached, and that the intercooler fins are neither clogged nor damaged.

OK:

The intake system pipes are not detached, and the intercooler fins are neither clogged nor damaged.



Result:
Proceed to
OK
NG



OK

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Start the engine and warm it up.


g.

Take a snapshot of the following Data List items.


h.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Intake Air Temperature and Intake Air Temperature B1S1 (Turbo).

Powertrain > Engine and Transmission > Data List
Tester Display
Intake Air Temperature
Intake Air Temperature B1S1 (Turbo)
50003 456 241,331

i.

Start the engine and drive the vehicle at 70 km/h (43.8 mph) for 10 minutes.

HINT:

Must not be during PM forced regeneration.



j.

Check the difference in temperature between Intake Air Temperature and Intake Air Temperature B1S1 (Turbo) using the recorded snapshot.

Result:
Result Proceed to
Except below A
Intake Air Temperature B1S1 (Turbo) is higher than Intake Air Temperature by 12°C or more B




A

END

B

5.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the intake air temperature sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

7.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E20-4 (THA) - E6-28 (THA) Always Below 1 Ω
E20-2 (E2G) - E6-29 (EVG) Always Below 1 Ω
E20-4 (THA) or E6-28 (THA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.INSPECT INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Inspect the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)

NG

10.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
9.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E24-2 (THA) - E5-26 (THIA) Always Below 1 Ω
E24-1 (E2) - E5-27 (E2) Always Below 1 Ω
E24-2 (THA) or E5-26 (THIA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED