The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 1 indoor electrical key antenna assembly removal/installation are shown below.
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
The procedure listed below is a representative example.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
If the front seat airbag assembly was deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
Replace any other damaged parts as necessary.
2.REMOVE FRONT SEAT ASSEMBLY LH
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
for Separate Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Separate Seat Type)>REMOVAL
for Sliding Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Sliding Bench Seat Type)>REMOVAL
3.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
4.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box)
86183E
5.REMOVE AUDIO AMPLIFIER COVER (for 12 Speakers)
6.REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 12 Speakers)
67912A
7.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH
67914B
8.REMOVE FRONT DOOR SCUFF PLATE LH
67911B
9.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE RH
Use the same procedure described for the LH side.
67913B
10.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62112
11.REMOVE COWL SIDE TRIM BOARD LH
62111C
12.REMOVE COWL SIDE TRIM BOARD RH
73233
13.REMOVE OUTER LAP BELT ANCHOR COVER
73220
14.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73210
15.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH side.
67917C
16.REMOVE REAR DOOR SCUFF PLATE RH
67918D
17.REMOVE REAR DOOR SCUFF PLATE LH
Use the same procedure described for the RH side.
74617A
18.REMOVE ASSIST GRIP PLUG
Use the same procedure for both assist grip plugs.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
74680
19.REMOVE PILLAR ASSIST GRIP ASSEMBLY B
Use the same procedure for both pillar assist grip assembly B.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
62312B
20.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Pull back the front door opening trim weatherstrip RH so that the lower center pillar garnish LH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>REMOVAL
62311B
21.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
67871E
22.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH
Pull back the No. 1 slide door weatherstrip RH so that the lower center pillar garnish RH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>REMOVAL
67872A
23.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH
Pull back the No. 1 slide door weatherstrip LH so that the lower center pillar garnish LH can be removed.
Use the same procedure described for the RH side.
62413A
24.REMOVE LOWER CENTER PILLAR GARNISH RH
62414A
25.REMOVE LOWER CENTER PILLAR GARNISH LH
Use the same procedure described for the RH side.
55641
26.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER
55642
27.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER
58534E
28.REMOVE CENTER FLOOR CARPET COVER LH
58533C
29.REMOVE CENTER FLOOR CARPET COVER RH
55646
30.REMOVE NO. 3 INSTRUMENT PANEL UNDER COVER
87212G
31.REMOVE REAR NO. 3 AIR DUCT (w/ Rear Foot Duct)
87212F
32.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Foot Duct)
58510D
33.REMOVE FRONT FLOOR CARPET ASSEMBLY
for LHD:
Using a clip remover, remove the 2 clips.
Detach each fastener and remove the front floor carpet assembly.
|
Fastener | - | - |
for RHD:
Using a clip remover, remove the 2 clips.
Detach each fastener and remove the front floor carpet assembly.
|
Fastener | - | - |
899A0
34.REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY
Do not reuse parts if dropped or subjected to any strong impact.
| *a | Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the No. 1 indoor electrical key antenna assembly.
Tape the thin-bladed screwdriver tip before use.
Disconnect the connector.