Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT (for LHD) › from 2019.06
RM35X0E _58 Vehicle Interior _079316 HEATING / AIR CONDITIONING _0384874 FRONT AIR CONDITIONING UNIT(for LHD) A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front air conditioning unit (for LHD) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement part or procedure Necessary procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 4.DRAIN ENGINE COOLANT

Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 47220D 6.DISCONNECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 55738D 7.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 88717A 9.DISCONNECT COOLER REFRIGERANT SUCTION PIPE A (w/o Sub-cool Accelerator)

a.
E400892C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt and rotate the 1-point tightening plate as shown in the illustration.


b.
E400893

Disconnect the cooler refrigerant suction pipe A.


c.

Remove the O-ring from the cooler refrigerant suction pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88716A 10.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (w/o Sub-cool Accelerator)

a.
E400894

Disconnect the cooler refrigerant liquid pipe A.


b.

Remove the O-ring from the cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88710C 11.DISCONNECT AIR CONDITIONING TUBE ASSEMBLY (w/ Sub-cool Accelerator)

a.
E400895C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt and rotate the 1-point tightening as shown in the illustration.


b.
E400896

Disconnect the air conditioning tube assembly.


c.

Remove the O-ring from the air conditioning tube assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 87246A 12.DISCONNECT HEATER WATER HOSE OUTLET A (for 1GD-FTV)

a.
E400897

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose outlet A.

NOTICE:
·

Do not apply excessive force to the water hose and heater water hose outlet A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245A 13.DISCONNECT HEATER WATER HOSE INLET A (for 1GD-FTV)

a.
E400898

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose inlet A.

NOTICE:
·

Do not apply excessive force to the water hose and heater water hose inlet A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245A 14.DISCONNECT HEATER WATER HOSE INLET A (for 7GR-FKS)

a.
E400942

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose inlet A.

NOTICE:
·

Do not apply excessive force to the water hose and heater water hose inlet A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87246A 15.DISCONNECT HEATER WATER HOSE OUTLET A (for 7GR-FKS)

a.
E400944

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose outlet A.

NOTICE:
·

Do not apply excessive force to the water hose and heater water hose outlet A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87128 16.REMOVE HEATER GROMMET

E400899

a.

Detach the claw and remove the heater grommet.


Hide 55301 18.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

Hide 20.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 87211 21.REMOVE NO. 1 AIR DUCT

E400900

a.

Remove the 2 bolts.


b.

Detach the claw and remove the No. 1 air duct.

NOTICE:
·

When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.

·

If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace with a new one.




Hide 87212G 22.REMOVE REAR NO. 3 AIR DUCT (w/ Rear Foot Duct)

a.
E421728C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear No. 3 air duct as shown in the illustration.


Hide 87212F 23.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Foot Duct)

E421729C01
0,0 0,0 false
V113147

Remove in this Direction


a.

Remove the rear No. 2 air duct as shown in the illustration.


Hide 45250 24.REMOVE STEERING COLUMN ASSEMBLY

Hide 33530K 25.REMOVE SHIFT LEVER ASSEMBLY (for Manual Transmission)

Hide 26.REMOVE TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY (for Automatic Transmission)

Hide 27.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73210 29.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)

HINT:

Use the same procedure described for the LH side.


Hide 74733 30.REMOVE NO. 1 HAND GRIP COVER (for Semi-trim, w/ Hand Rail)

Hide 74707 31.REMOVE NO. 1 HAND GRIP FRAME SUB-ASSEMBLY (for Semi-trim, w/ Hand Rail)

Hide 74617A 33.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)

Hide 74680 34.REMOVE PILLAR ASSIST GRIP ASSEMBLY B (w/ Assist Grip)

Hide 62413A 35.REMOVE LOWER CENTER PILLAR GARNISH RH

Hide 67918D 36.REMOVE REAR DOOR SCUFF PLATE LH (for 5 Door)

HINT:

Use the same procedure described for the RH side.



Hide 62414A 37.REMOVE LOWER CENTER PILLAR GARNISH LH (for 5 Door)

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 67935 38.REMOVE BACK DOOR SCUFF PLATE (for 4 Door)

Hide 73570B 39.REMOVE REAR SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR) (for 4 Door, w/ Seat Belt)

Hide 58777A 40.REMOVE TOOL BAG HOLDER (for 4 Door)

Hide 62640M 41.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY LH (for 4 Door)

Hide 62620K 42.REMOVE SIDE TRIM BOARD ASSEMBLY LH (for High Roof)

Hide 62520B 43.REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for 4 Door)

Hide 58510D 44.REMOVE FRONT FLOOR CARPET ASSEMBLY

a.

w/ Console Box:

i.

Using a clip remover, remove the 4 clips.

E400901C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Fastener



ii.

Detach each fastener.


iii.

Fold back the front floor carpet assembly as shown in the illustration.



b.

w/o Console Box:

i.

Using a clip remover, remove the 4 clips.

E416477C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Fastener



ii.

Detach each fastener.


iii.

Fold back the front floor carpet assembly as shown in the illustration.



Hide 58193G 45.REMOVE NO. 3 FRONT FLOOR FOOTREST

a.
E400902

Using a clip remover, detach the clip and remove the No. 3 front floor footrest.


Hide 82141 46.DISCONNECT INSTRUMENT PANEL WIRE

a.

Remove each bolt and each ground wire.

E400903C01
3.167,0.417 2.979,0.302 true 5.99,7.469 6.198,7.667 0.208,0.198 12 true *A 0.448,6.094 0.656,6.292 0.208,0.198 10 true *1 6.031,5.479 6.24,5.677 0.208,0.198 10 true *1 6.354,5.167 6.563,5.365 0.208,0.198 10 true *1 6.198,7.844 6.406,8.042 0.208,0.198 12 true *A 5.948,8.5 6.156,8.698 0.208,0.198 12 true *A 3.708,1.938 3.917,2.135 0.208,0.198 10 true *1 5.854,5.854 6.01,6.042 0.156,0.188 10 true A 2.781,0.229 2.99,0.406 0.208,0.177 10 true *2
*A w/ PTC Heater - -
*1 Ground Wire *2 Protector Cover
V100135

Connector
V100136

Bolt
V100137

Nut
V113147

Remove in this Direction



b.

Disconnect each connector and detach each clamp.


c.

Remove each nut and then disconnect the instrument panel wire.


Hide 55950G 47.REMOVE DEFROSTER NOZZLE ASSEMBLY

a.
E400907

Detach the claw and remove the defroster nozzle assembly.


Hide 87201A 48.REMOVE AIR DUCT SUB-ASSEMBLY

a.
E400904

Remove the 2 nuts and air duct sub-assembly.


Hide 55306A 49.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E400905C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 nuts.


b.

Remove the 3 bolts and No. 1 instrument panel brace sub-assembly.


Hide 55307C 50.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E400906C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Screw


Remove the nut and screw.


b.

Remove the 2 bolts and No. 2 instrument panel brace sub-assembly.


Hide 88650N 51.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 52.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.

·

Be careful not to damage the internal components of the instrument panel reinforcement assembly with air conditioning unit assembly on the glass etc. Only perform removal after first taking the appropriate actions.

·

Do not allow the instrument panel reinforcement assembly with air conditioning unit assembly to strike the airbag ECU assembly. Doing so may damage the heater case, causing water leaks.



a.
E400908

Disconnect the drain cooler hose.


b.

Remove the nut.


c.

for Automatic Transmission:

i.

Remove the 8 bolts.

E400909C01
0.938,0.115 1.167,0.323 0.229,0.208 10 true *a 0.375,3.813 0.635,4.042 0.26,0.229 12 true *A
*A for Manual Transmission - -
*a Engine Room Side - -
V100135

Bolt A
V100136

Bolt B




d.

for Manual Transmission:

i.

Remove the 9 bolts.



e.

Remove the instrument panel reinforcement assembly with air conditioner unit assembly.

NOTICE:
When carrying the instrument panel reinforcement assembly with air conditioning unit assembly, hold the bottom of the assembly. Do not hold the following parts.
·

Do not hold the air conditioning harness assembly. Otherwise, static electricity from the technician may damage the air conditioning harness assembly.

·

Do not hold the heater core or pipe of the heater radiator unit sub-assembly. Otherwise, the pipe may detach, the clamp may be damaged, or the crimped areas of the heater core and pipe of the heater radiator unit sub-assembly may be damaged, causing coolant to leak.

·

Do not hold the air conditioning radiator damper servo sub-assembly, blower damper servo sub-assembly or link. Otherwise, the servo motor may become misaligned, causing abnormal operation noise, temperature control defects, or air leaks due to sealing defects in the doors.

·

Do not hold the door. Doing so may cause air leaks due to closing defects resulting from excessive opening/closing. Also, keep the door free from oil and grease.




Hide 53.REMOVE AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.

·

Be careful not to damage the internal components of the instrument panel reinforcement assembly and air conditioning unit assembly on the glass etc. Only perform removal after first taking the appropriate actions.

·

Store the air conditioning unit assembly in a location free from sand and other foreign matter.



a.

Remove the 4 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.

E400910

NOTICE:
When carrying the air conditioning unit assembly, hold the bottom of the assembly. Do not hold the following parts.
·

Do not hold the air conditioning harness assembly. Otherwise, static electricity from the technician may damage the air conditioning harness assembly.

·

Do not hold the heater core or pipe of the heater radiator unit sub-assembly. Otherwise, the pipe may detach, the clamp may be damaged, or the crimped areas of the heater core and pipe of the heater radiator unit sub-assembly may be damaged, causing coolant to leak.

·

Do not hold the air conditioning radiator damper servo sub-assembly, blower damper servo sub-assembly or link. Otherwise, the servo motor may become misaligned, causing abnormal operation noise, temperature control defects, or air leaks due to sealing defects in the doors.

·

Do not hold the door. Doing so may cause air leaks due to closing defects resulting from excessive opening/closing. Also, keep the door free from oil and grease.




Hide 51406A 54.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2cooler unit drain hose is necessary.



Hide 52618 55.REMOVE LOWER FRONT BUMPER ABSORBER

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2cooler unit drain hose is necessary.



Hide 51405A 56.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2cooler unit drain hose is necessary.



Hide 88539 57.REMOVE NO. 1 COOLER UNIT DRAIN HOSE

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose is necessary.


a.
E400911

Disconnect the No. 1 cooler unit drain hose from cooler unit drain pipe.


b.
E400912C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 1 cooler unit drain hose.

NOTICE:

Install the No. 1 cooler unit drain hose with its paint mark facing upward.



Hide 88539C 58.REMOVE NO. 2 COOLER UNIT DRAIN HOSE

HINT:

Perform this procedure only when replacement of the No. 2 cooler unit drain hose is necessary.


a.
E400913

Remove the bolt and detach the clamp.


b.

Remove the cooler unit drain pipe with No. 2 cooler unit drain hose.


c.
E400914

Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 cooler unit drain hose from cooler unit drain pipe.


Hide 88539D 59.REMOVE COOLER UNIT DRAIN PIPE

HINT:

Perform this procedure only when replacement of the cooler unit drain pipe is necessary.


a.
E417311

Remove the 2 screws and piping clamp.