Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT (for RHD) › 2019.06–2020.05
RM35X0E _58 Vehicle Interior _079316 HEATING / AIR CONDITIONING _0384875 FRONT AIR CONDITIONING UNIT(for RHD) A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front air conditioning unit (for RHD) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement part or procedure Necessary procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 4.DRAIN ENGINE COOLANT

Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 47220D 6.DISCONNECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 55738D 7.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 88717A 9.DISCONNECT COOLER REFRIGERANT SUCTION PIPE A (w/o Sub-cool Accelerator)

a.
E415159C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt and rotate the 1-point tightening plate as shown in the illustration.


b.
E415160

Disconnect the cooler refrigerant suction pipe A.


c.

Remove the O-ring from the cooler refrigerant suction pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88716A 10.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (w/o Sub-cool Accelerator)

a.
E415161

Disconnect the cooler refrigerant liquid pipe A.


b.

Remove the O-ring from the cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88710C 11.DISCONNECT AIR CONDITIONING TUBE ASSEMBLY (w/ Sub-cool Accelerator)

a.
E415162C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt and rotate the 1-point tightening as shown in the illustration.


b.
E415163

Disconnect the air conditioning tube assembly.


c.

Remove the O-ring from the air conditioning tube assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 87246A 12.DISCONNECT HEATER WATER HOSE OUTLET A (for 1GD-FTV)

a.
E415164

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose outlet A.

NOTICE:
·

Do not apply excessive force to the water hose and heater water hose outlet A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245A 13.DISCONNECT HEATER WATER HOSE INLET A (for 1GD-FTV)

a.
E415166

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose inlet A.

NOTICE:
·

Do not apply excessive force to the water hose and heater water hose inlet A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245A 14.DISCONNECT HEATER WATER HOSE INLET A (for 7GR-FKS)

a.
E415167

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose inlet A.

NOTICE:
·

Do not apply excessive force to the water hose and heater water hose inlet A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87246A 15.DISCONNECT HEATER WATER HOSE OUTLET A (for 7GR-FKS)

a.
E415165

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose outlet A.

NOTICE:
·

Do not apply excessive force to the water hose and heater water hose outlet A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87128 16.REMOVE HEATER GROMMET

a.
E415168

Detach the claw and remove the heater grommet.


Hide 55301 18.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

Hide 19.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 87211 20.REMOVE NO. 1 AIR DUCT

a.
E415169

Remove the 2 bolts.


b.

Detach the claw and remove the No. 1 air duct.

NOTICE:
·

When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.

·

If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace with a new one.




Hide 87212G 21.REMOVE REAR NO. 3 AIR DUCT (w/ Rear Foot Duct)

a.
E416505C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear No. 3 air duct as shown in the illustration.


Hide 87212F 22.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Foot Duct)

E416507C01
0,0 0,0 false
V113147

Remove in this Direction


a.

Remove the rear No. 2 air duct as shown in the illustration.


Hide 45250 23.REMOVE STEERING COLUMN ASSEMBLY

Hide 33530K 24.REMOVE SHIFT LEVER ASSEMBLY (for Manual Transmission)

Hide 25.REMOVE TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY (for Automatic Transmission)

Hide 73210 28.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)

HINT:

Use the same procedure described for the LH side.


Hide 74733 29.REMOVE NO. 1 HAND GRIP COVER (w/ Hand Rail)

Hide 74708 30.REMOVE NO. 2 HAND GRIP FRAME SUB-ASSEMBLY (w/ Hand Rail)

Hide 67918D 31.REMOVE REAR DOOR SCUFF PLATE LH

Hide 74617A 32.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)

HINT:

Use the same procedure for both assist grip plugs.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 74680 33.REMOVE PILLAR ASSIST GRIP ASSEMBLY B (w/ Assist Grip)

Hide 62414A 34.REMOVE LOWER CENTER PILLAR GARNISH LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 67917C 35.REMOVE REAR DOOR SCUFF PLATE RH (for 5 Door)

Hide 62413A 36.REMOVE LOWER CENTER PILLAR GARNISH RH (for 5 Door)

Hide 67935 37.REMOVE BACK DOOR SCUFF PLATE (for 4 Door)

Hide 73570B 38.REMOVE REAR SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR) (for 4 Door, w/ Seat Belt)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY (for Full-trim)>REMOVAL


Hide 62630L 39.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY RH (for 4 Door)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 62610K 40.REMOVE SIDE TRIM BOARD ASSEMBLY RH (for High Roof, for Full-trim)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 62510M 41.REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for 4 Door)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL


Hide 58510D 42.REMOVE FRONT FLOOR CARPET ASSEMBLY

a.

w/ Console Box:

i.

Using a clip remover, remove the 4 clips.

E415170C01
0,0 0,0 false
V100155

Fastener
V113147

Remove in this Direction



ii.

Detach each fastener.


iii.

Fold back the front floor carpet assembly as shown in the illustration.



b.

w/o Console Box:

i.

Using a clip remover, remove the 4 clips.

E415171C01
0,0 0,0 false
V100155

Fastener
V113147

Remove in this Direction



ii.

Detach each fastener.


iii.

Fold back the front floor carpet assembly as shown in the illustration.



Hide 58193G 43.REMOVE NO. 3 FRONT FLOOR FOOTREST

a.
E415172

Using a clip remover, detach the clip and remove the No. 3 front floor footrest.


Hide 82141 44.DISCONNECT INSTRUMENT PANEL WIRE

a.

Remove each bolt and each ground wire.

E415173C01
3.667,0.5 3.75,0.333 3.75,0.333 3.917,0.333 true 0.167,1.313 0.344,1.458 0.177,0.146 10 true *1 0.313,1.469 0.49,1.615 0.177,0.146 10 true *1 6.135,2.531 6.313,2.698 0.177,0.167 10 true *1 6.146,5.688 6.323,5.854 0.177,0.167 10 true *1 6.094,5.448 6.271,5.615 0.177,0.167 10 true *1 0.323,7.51 0.563,7.719 0.24,0.208 12 true *A 2.813,1.833 3.052,2.031 0.24,0.198 12 true *B 3.99,0.26 4.198,0.438 0.208,0.177 10 true *2 0.948,1.417 1.104,1.615 0.156,0.198 10 true A
*A w/ PTC Heater *B w/ VFC ECU
*1 Ground Wire *2 Protector Cover
V100135

Connector
V100136

Bolt
V100137

Nut
V113147

Remove in this Direction



b.

Detach the claw and open the protector cover.


c.

Detach the claw and remove the protector cover together with the instrument panel wire.


d.

Disconnect each connector and detach each clamp.


e.

Remove the nut and then disconnect the instrument panel wire.


Hide 55950G 45.REMOVE DEFROSTER NOZZLE ASSEMBLY

a.
E415177

Detach the claw and remove the defroster nozzle assembly.


Hide 87201A 46.REMOVE AIR DUCT SUB-ASSEMBLY

a.
E415174

Remove the 2 nuts and air duct sub-assembly.


Hide 55306A 47.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E415175C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 3 bolts, 2 nuts and No. 1 instrument panel brace sub-assembly.


Hide 55307C 48.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E415176C01
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Remove the nut and screw.


b.

Remove the 2 bolts and No. 2 instrument panel brace sub-assembly.


Hide 88650N 49.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 50.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.

·

Be careful not to damage the internal components of the instrument panel reinforcement assembly with air conditioning unit assembly on the glass etc. Only perform removal after first taking the appropriate actions.

·

Do not allow the instrument panel reinforcement assembly with air conditioning unit assembly to strike the airbag ECU assembly. Doing so may damage the heater case, causing water leaks.



a.
E415178

Disconnect the drain cooler hose.


b.

Remove the nut.


c.

for Automatic Transmission:

i.

Remove the 8 bolts.

E415134C01
0.969,0.135 1.177,0.333 0.208,0.198 10 true *a 4.167,2.833 4.365,3.021 0.198,0.188 12 true *A
*A for Manual Transmission - -
*a Engine Room Side - -
V100135

Bolt A
V100136

Bolt B




d.

for Manual Transmission:

i.

Remove the 9 bolts.



e.

Remove the instrument panel reinforcement assembly with air conditioner unit assembly.

NOTICE:
When carrying the instrument panel reinforcement assembly with air conditioning unit assembly, hold the bottom of the assembly. Do not hold the following parts.
·

Do not hold the air conditioning harness assembly. Otherwise, static electricity from the technician may damage the air conditioning harness assembly.

·

Do not hold the heater core or pipe of the heater radiator unit sub-assembly. Otherwise, the pipe may detach, the clamp may be damaged, or the crimped areas of the heater core and pipe of the heater radiator unit sub-assembly may be damaged, causing coolant to leak.

·

Do not hold the air conditioning radiator damper servo sub-assembly, blower damper servo sub-assembly or link. Otherwise, the servo motor may become misaligned, causing abnormal operation noise, temperature control defects, or air leaks due to sealing defects in the doors.

·

Do not hold the door. Doing so may cause air leaks due to closing defects resulting from excessive opening/closing. Also, keep the door free from oil and grease.




Hide 51.REMOVE AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.

·

Be careful not to damage the internal components of the instrument panel reinforcement assembly and air conditioning unit assembly on the glass etc. Only perform removal after first taking the appropriate actions.

·

Store the air conditioning unit assembly in a location free from sand and other foreign matter.



a.

Remove the 4 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.

E415179

NOTICE:
When carrying the air conditioning unit assembly, hold the bottom of the assembly. Do not hold the following parts.
·

Do not hold the air conditioning harness assembly. Otherwise, static electricity from the technician may damage the air conditioning harness assembly.

·

Do not hold the heater core or pipe of the heater radiator unit sub-assembly. Otherwise, the pipe may detach, the clamp may be damaged, or the crimped areas of the heater core and pipe of the heater radiator unit sub-assembly may be damaged, causing coolant to leak.

·

Do not hold the air conditioning radiator damper servo sub-assembly, blower damper servo sub-assembly or link. Otherwise, the servo motor may become misaligned, causing abnormal operation noise, temperature control defects, or air leaks due to sealing defects in the doors.

·

Do not hold the door. Doing so may cause air leaks due to closing defects resulting from excessive opening/closing. Also, keep the door free from oil and grease.




Hide 51406A 52.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2 cooler unit drain hose is necessary.



Hide 52618 53.REMOVE LOWER FRONT BUMPER ABSORBER

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2 cooler unit drain hose is necessary.



Hide 51405A 54.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2 cooler unit drain hose is necessary.



Hide 23300 55.REMOVE FUEL FILTER ASSEMBLY (for 1GD-FTV)

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2 cooler unit drain hose is necessary.


Hide 88539 56.REMOVE NO. 1 COOLER UNIT DRAIN HOSE

HINT:

Perform this procedure only when replacement of the No. 1 cooler unit drain hose is necessary.


a.
E415180

Disconnect the No. 1 cooler unit drain hose from cooler unit drain pipe.


b.
E415181C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 1 cooler unit drain hose.

NOTICE:

Install the No. 1 cooler unit drain hose with its paint mark facing upward.



Hide 88539C 57.REMOVE NO. 2 COOLER UNIT DRAIN HOSE

HINT:

Perform this procedure only when replacement of the No. 2 cooler unit drain hose is necessary.


a.
E415182

Remove the bolt and detach the clamp.


b.

Remove the No. 2 cooler unit drain hose together with the cooler unit drain pipe.


c.
E415183

Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 cooler unit drain hose from cooler unit drain pipe.


Hide 88539D 58.REMOVE COOLER UNIT DRAIN PIPE

HINT:

Perform this procedure only when replacement of the cooler unit drain pipe is necessary.


a.
E417312

Remove the 2 screws and piping clamp.