Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Center Pillar) › from 2019.06
RM35X0E _58 Vehicle Interior _079257 SUPPLEMENTAL RESTRAINT SYSTEMS _0384945 SIDE AIRBAG SENSOR(for Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Center Pillar)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89831A 1.INSTALL NO. 1 SIDE AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B524596

Attach the guide and hold the No. 1 side airbag sensor in place.

NOTICE:
·

If the No. 1 side airbag sensor has been dropped, replace it with a new one.

·

When installing the No. 1 side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.




d.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Tighten the bolt while holding the No. 1 side airbag sensor because the No. 1 side airbag sensor guide is easily damaged.



e.

Check that there is no looseness in the installation parts of the No. 1 side airbag sensor.


f.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:




Hide 62414A 2.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Install the lower center pillar garnish LH.

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>INSTALLATION



b.

Return the front door opening trim weatherstrip LH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


c.

for Slide Door Side:

Return the No. 1 slide door weatherstrip LH to its original position.

i.

for Wagon:

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>INSTALLATION



ii.

except Wagon:

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (except Wagon)>INSTALLATION




Hide 74680 3.INSTALL PILLAR ASSIST GRIP ASSEMBLY B (except Wagon, w/ Assist Grip)

Hide 74617A 4.INSTALL ASSIST GRIP PLUG (except Wagon, w/ Assist Grip)

Hide 74680 5.INSTALL PILLAR ASSIST GRIP ASSEMBLY B (for Wagon)

Hide 74617A 6.INSTALL ASSIST GRIP PLUG (for Wagon)

Hide 73220 7.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

Hide 67918D 9.INSTALL REAR DOOR SCUFF PLATE LH (for Slide Door Side)

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Semi-trim)>INSTALLATION


Hide 67914B 10.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 67912A 11.INSTALL FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 13. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART