The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear floor side airbag sensor removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE REAR NO. 3 SEAT ASSEMBLY
for 60/40 Split Seat Type 40 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
for 60/40 Split Seat Type 60 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
4.REMOVE REAR SEAT ASSEMBLY
for Folding Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
73233
5.REMOVE OUTER LAP BELT ANCHOR COVER (w/ Seat Belt)
73560A
6.REMOVE NO. 3 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) (w/ Seat Belt)
Use the same procedure described for the LH side.
Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY (for Wagon)>REMOVAL
67881A
7.REMOVE BACK DOOR WEATHERSTRIP
67935
8.REMOVE BACK DOOR SCUFF PLATE
67871E
9.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH
Remove the rear side of the No. 1 slide door weatherstrip RH so that the rear quarter trim board assembly RH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>REMOVAL
62510M
10.REMOVE QUARTER TRIM PANEL ASSEMBLY RH
11.REMOVE REAR SEAT TRACK SLIDE STOPPER
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
58595
12.REMOVE NO. 3 FLOOR CARPET MOULDING NO. 1
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
58595
13.REMOVE NO. 3 FLOOR CARPET MOULDING NO. 2
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
14.REMOVE SEAT TRACK RAIL PROTECTOR
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
58570C
15.REMOVE REAR FLOOR CARPET ASSEMBLY
Fold back the rear floor carpet assembly as shown in the illustration.
| *A | for Type A | *B | for Type B |
| *C | for Type C | *D | for Type D |
|
Fold Back | - | - |
58513F
16.REMOVE NO. 3 FLOOR MAT
89839A
17.REMOVE REAR FLOOR SIDE AIRBAG SENSOR COVER
Remove the rear floor side airbag sensor cover.
If the rear floor side airbag sensor cover is removed, do not reuse it.
89837A
18.REMOVE REAR FLOOR SIDE AIRBAG SENSOR
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR
Remove the bolt.
Loosen the bolt while holding the rear floor side airbag sensor because the rear floor side airbag sensor guide is easily damaged.
If the rear floor side airbag sensor has been dropped, replace it with a new one.
Detach the guide to remove the rear floor side airbag sensor.
19.REMOVE CLIP
If the clip is removed, do not reuse it.
Perform this procedure only when replacement of the clip is necessary.
Detach claw and remove the clip.