The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the fuel lid lock control cable sub-assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION (w/ Front Seat Side Airbag)
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)
for 7GR-FKS:
for 1GD-FTV:
Click hereGeneral>MAINTENANCE>1GD-FTV BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE FRONT SEAT ASSEMBLY
Use the same procedure for the RH and LH sides.
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
for Separate Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Separate Seat Type)>REMOVAL
for Fixed Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Fixed Bench Seat Type)>REMOVAL
for Sliding Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Sliding Bench Seat Type)>REMOVAL
67911B
4.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
67913B
5.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
62111C
6.REMOVE COWL SIDE TRIM BOARD RH
7.REMOVE FRONT CONSOLE BOX (w/ Console Box)
73220
8.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH
for Semi-trim:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Semi-trim)>REMOVAL
for Full-trim:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Full-trim)>REMOVAL
for Wagon:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Wagon)>REMOVAL
55641
9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER
77306
10.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the claw in the direction (1) indicated by the arrow shown in the illustration.
Detach the guide in the direction (2) indicated by the arrow shown in the illustration and remove the fuel lid lock open lever sub-assembly.
Detach the clamp and remove the fuel lid lock open lever sub-assembly from the fuel lid lock control cable sub-assembly.
77035
11.DISCONNECT FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
|
Remove in this Direction |
Fold back the front floor mat assembly enough so that the fuel lid lock control cable can be removed as shown in the illustration.
Detach the clamp and disconnect the fuel lid lock control cable sub-assembly.
77310A
12.REMOVE FUEL TANK CAP ASSEMBLY
|
Remove in this Direction |
Remove the fuel tank cap assembly as shown in the illustration.
Detach the clamp and remove the fuel tank cap assembly.
w/ Urea SCR System:
Use the same procedure to remove the fuel inlet box ring.
77293A
13.REMOVE NO. 3 FUEL TANK FILLER PIPE SHIELD
|
Protective Tape |
Apply protective tape around the fuel filler opening lid assembly as shown in the illustration.
Remove the fuel inlet box ring as shown in the illustration.
| *1 | Fuel Inlet Box Ring | - | - |
w/ Urea SCR System:
Use the same procedure to remove the fuel inlet box ring.
While pushing the fuel tank filler pipe shield assembly into the vehicle, disconnect the fuel tank filler pipe shield assembly from the No. 3 fuel tank filler pipe shield as shown in the illustration.
w/ Urea SCR System:
Use the same procedure to disconnect the fuel tank filler pipe shield assembly.
Using a 4 mm hexagon socket wrench, remove the 7 screws.
|
Remove in this Direction |
Pull the No. 3 fuel tank filler pipe shield in the direction of the arrow shown in the illustration and remove it together with the fuel lid lock control cable sub-assembly.
Pull the fuel lid lock control cable sub-assembly out of the vehicle.
Detach the claw and remove the 7 grommets.
77035
14.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
Detach the clamp and remove the fuel lid lock control cable sub-assembly from the fuel filler opening lid lock sub-assembly.
77037
15.REMOVE FUEL FILLER OPENING LID LOCK SUB-ASSEMBLY
Perform this procedure only when replacement of the fuel filler opening lid lock sub-assembly is necessary.
Remove the nut and fuel filler opening lid lock sub-assembly.
77378A
16.REMOVE FUEL FILLER OPENING LID LOCK COVER
Perform this procedure only when replacement of the fuel filler opening lid lock cover is necessary.
Detach the clip and remove the fuel filler opening lid lock cover.