The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the courtesy light wire removal/installation are shown below.
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the RH side.
84234
1.REMOVE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY
Using a T30 "TORX" socket wrench, remove the "TORX" screw and rear door courtesy light switch assembly.
Disconnect the connector.
2. PRECAUTION (for First Row)
Perform this procedure only when replacing the courtesy light wire.
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
If the pretensioner has been deployed, replace any damaged parts as necessary.
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for First Row)
Perform this procedure only when replacing the courtesy light wire.
Operate the rear power seat switch and move the ottoman to the uppermost position and seatback to the frontmost position.
Disconnet the cable from the negative (-) battery terminal.
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
4.REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for LH Side)
Perform this procedure only when replacing the courtesy light wire.
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
5.REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for RH Side)
Perform this procedure only when replacing the courtesy light wire.
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
6.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for LH Side)
Perform this procedure only when replacing the courtesy light wire.
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
7.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for RH Side)
Perform this procedure only when replacing the courtesy light wire.
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
8.REMOVE REAR NO. 3 SEAT ASSEMBLY LH (for LH Side)
Perform this procedure only when replacing the courtesy light wire.
for Folding Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for 60/40 Split Seat Type 40 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
9.REMOVE REAR NO. 3 SEAT ASSEMBLY RH (for RH Side)
Perform this procedure only when replacing the courtesy light wire.
for Folding Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for 60/40 Split Seat Type 60 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
73233D
10.REMOVE OUTER LAP BELT ANCHOR COVER (w/ Seat Belt)
Perform this procedure only when replacing the courtesy light wire.
Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY (for Wagon)>REMOVAL
11.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) (w/ Seat Belt)
Perform this procedure only when replacing the courtesy light wire.
Use the same procedure described for the LH side.
Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY (for Wagon)>REMOVAL
67935
12.REMOVE BACK DOOR SCUFF PLATE
Perform this procedure only when replacing the courtesy light wire.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
67917C
13.REMOVE REAR DOOR SCUFF PLATE RH
Perform this procedure only when replacing the courtesy light wire.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
67871E
14.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH
Perform this procedure only when replacing the courtesy light wire.
Pull back the No. 1 slide door weatherstrip RH so that the quarter trim assembly RH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>REMOVAL
62510M
15.REMOVE QUARTER TRIM PANEL ASSEMBLY RH
Perform this procedure only when replacing the courtesy light wire.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
82351B
16.REMOVE COURTESY LIGHT WIRE
Perform this procedure only when replacing the courtesy light wire.
Disconnect the 2 connectors and remove the courtesy light wire.