Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE › 2019.06–2020.05
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0384422 ENGINE G

1GD-FTV ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343690

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running.


PROCEDURE

Hide 16620 4.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

Hide 13750 5.CHECK VALVE LASH ADJUSTER NOISE

a.

Warm up the engine.


b.

Rev the engine several times. Check that the engine does not emit unusual noises.

If unusual noises occur, warm up the engine and idle it for more than 30 minutes. Then perform the inspection above again.

If any defects or problems are found during the inspection above, perform a valve lash adjuster inspection.


Hide 17801 6.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case.


b.

Check that the air cleaner filter element sub-assembly is not excessively dirty.

If the air cleaner filter element sub-assembly is excessively dirty, replace the air cleaner filter element sub-assembly.

If cleaning the air cleaner filter element sub-assembly. blow compressed air to clean it.

NOTICE:
·

Do not start the engine with the air cleaner filter element sub-assembly removed, as this may damage the engine.

·

When using an air cleaner filter element sub-assembly that uses compressed air, wear safety glasses and a dust mask in order to protect your health.



HINT:

When an excessive amount of dirt is present, replace the air cleaner filter element sub-assembly.



c.

Reinstall the air cleaner filter element sub-assembly to the air cleaner case.


Hide 7.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

Connect the GTS to the DLC3.


c.

Start the engine and idle it.


d.

w/o Exhaust Gas Temperature Sensor for EGR:

i.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211


e.

w/ Exhaust Gas Temperature Sensor for EGR:

i.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Engine Speed.

Powertrain > Engine and Transmission > Data List
Tester Display
Engine Speed
50003 456 238


f.

Inspect the engine idle speed.

Standard idle speed:

700 to 800 rpm


NOTICE:
·

Turn all the electrical systems and A/C off.

·

When checking the idle speed, move the shift lever to neutral.




g.

Turn the ignition switch off.


h.

Disconnect the GTS or tachometer tester probe from the DLC3.


Hide 8.INSPECT MAXIMUM ENGINE SPEED

a.

Start the engine.


b.

Fully depress the accelerator pedal.


c.

Check the maximum engine speed.

Maximum engine speed:

4450 to 4750 rpm



Hide 9.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Remove the 4 injector assemblies.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL


c.

Inspect the cylinder compression pressure.

i.
A340280C01
0.896,0.25 1.479,0.25 true 0.885,0.833 1.469,0.833 true 0.74,1.479 0.885,1.479 0.885,1.479 1.323,1.313 true 1.729,1.365 2.313,1.365 true 1.75,2.938 2.219,3.156 2.219,3.156 2.385,3.156 true 1.729,1.917 2.146,1.75 2.146,1.75 2.313,1.75 true 1.719,2.198 2.146,2.365 2.146,2.365 2.313,2.365 true 0.708,0.135 0.938,0.302 0.229,0.167 10 false *1 0.708,0.729 0.938,0.896 0.229,0.167 10 false *2 0.552,1.375 0.781,1.542 0.229,0.167 10 false *3 2.333,1.26 2.583,1.417 0.25,0.156 10 true *a 2.396,3.021 2.604,3.219 0.208,0.198 10 true *d 2.333,2.26 2.563,2.427 0.229,0.167 10 true *c 2.333,1.646 2.563,1.813 0.229,0.167 10 true *b
*1 Bolt
*2 Washer
*3 Nozzle Holder Clamp
*a SST (Attachment I)
*b New O-Ring
*c New Injection Nozzle Seat
*d New Nozzle Holder Gasket


Install a new nozzle holder gasket, new injection nozzle seat, new O-ring, SST (attachment I), nozzle holder clamp and washer to the cylinder head cover sub-assembly with the bolt.

SST
09992-19015  (09992-10120)

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


ii.
A340281C01
0.833,0.354 1.146,0.188 1.146,0.188 1.313,0.188 false 2.094,1.49 2.417,1.042 2.417,1.042 2.583,1.042 true 1.333,0.073 1.563,0.229 0.229,0.156 10 true *a 2.594,0.938 2.844,1.104 0.25,0.167 10 true *b
*a SST (Compression Gauge)
*b SST (L-joint)


Connect SST (gauge assembly), SST (packing set) and SST (L-joint) to SST (attachment I).

SST
09992-19015  (09992-10010, 09992-10020, 09992-10030)


iii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

2700 kPa (27.5 kgf/cm2, 392 psi) or higher


Minimum pressure:

2200 kPa (22.4 kgf/cm2, 319 psi)


Difference between each cylinder:

500 kPa (5.1 kgf/cm2, 73 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 280 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression as quickly as possible.




iv.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the injector holes, and then inspect it again.

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.



d.

Remove SST.


e.

Install the 4 injector assemblies.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>INSTALLATION