Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P24A200  Particulate Filter Regeneration Incomplete Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P24A200 Particulate Filter Regeneration Incomplete Bank 1 The catalyst temperature did not sufficiently increase during automatic PM regeneration and the regeneration time has become too long (1 trip detection logic).
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Class B1 DTC stored SAE Code: P24A2

MONITOR DESCRIPTION

When the catalyst temperature does not sufficiently increase during automatic PM regeneration and the regeneration time becomes too long, P24A200 is stored and PM regeneration for that trip is prohibited.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P24A200 PM forced regeneration

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the exhaust manifold converter sub-assembly (DPF catalyst), clear the thermal deterioration data stored in the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION

·

After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Record the stored DTC and freeze frame data.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

e.

Check Exhaust Fuel Addition F/B Bank 1 and Catalyst Differential Pressure Bank 1 in the freeze frame data.

HINT:
·

When the "Exhaust Fuel Addition F/B Bank 1" value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.

·

When the Catalyst Differential Pressure Bank 1 value is more than 0.27, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P24A200)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P24A200)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 456
Result:
Result Proceed to
DTC P24A200 is output A
Other relevant DTCs are output B




B

3.GO TO DTC CHART

A

4.CHECK FOR BLACK SMOKE
3.GO TO DTC CHART

NEXT

4.CHECK FOR BLACK SMOKE
4.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



NG

5.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

OK

6.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
5.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

6.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
6.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
a.

Remove the EFI-MAIN fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-MAIN fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Turn the engine switch on (IG).


c.

Turn the engine switch off and wait for 30 seconds or more.


d.

Turn the engine switch on (IG) and wait for 10 seconds or more.


e.

Connect the GTS to the DLC3.


f.

Turn the engine switch on (IG) and turn the GTS on.


g.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


h.

Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.

HINT:
·

If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.

·

When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.




i.

Enter the following menus: Powertrain / Engine and Transmission / Utility / PM Regenerate Mode.

Powertrain > Engine and Transmission > Utility
Tester Display
PM Regenerate Mode
50005 456 4576

j.

Enter PM Regenerate Mode.

CAUTION:

Be careful of the exhaust pipes and surrounding areas, as they become extremely hot when performing PM forced regeneration.



k.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S2 and DPNR/DPF Status Regeneration (PM).

Powertrain > Engine and Transmission > Data List
Tester Display
Exhaust Temperature B1S2
DPNR/DPF Status Regeneration (PM)
50003 456 340,193

l.

Check for temperature increases and abnormal white smoke during PM forced regeneration.

HINT:
·

PM forced regeneration takes 15 to 40 minutes to finish.

·

The time it takes to complete PM forced regeneration changes depending on "PM Accumulation Ratio Bank 1" and the vehicle operating conditions.

·

If the value of "Catalyst Differential Pressure Bank 1" increases too much during the PM forced regeneration, the fail-safe function activates and PM forced regeneration is stopped.

·

Perform PM forced regeneration control until the display on the multi-information display turns off.

·

If actions such as depressing the accelerator pedal or operating the DPF switch, etc. are performed during PM forced regeneration, PM forced regeneration stops. If PM forced regeneration stops, it is necessary to perform it again.

·

PM forced regeneration control is not complete until the display on the multi-information display turns off.



Result:
Result Proceed to
During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 500 to 590°C and abnormal white smoke is generated*1 A
During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 500 to 590°C and no white smoke is generated B
Other than above*2 C


HINT:
·

*1: If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst.

·

*1: When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.

·

*2: An excess of accumulated PM is the result of a malfunction in the control system causing poor combustion and an increase in black smoke.





A

7.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

B

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

10.CHECK FUEL INJECTION SYSTEM
7.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst. When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.



Result:
Proceed to
NEXT



NEXT

11.CHECK INTAKE/EXHAUST SYSTEM
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.

HINT:

If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst. When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.



Result:
Proceed to
NEXT



NEXT

9.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY AND NO. 1 INJECTOR HOLDER
9.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY AND NO. 1 INJECTOR HOLDER
a.

It has been determined that the exhaust fuel addition injector assembly and No. 1 injector holder needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust fuel addition injector assembly and No. 1 injector holder.

HINT:

If there is no malfunction in the electrical system, Exhaust Temperature B1S2 is 500°C (932°F) or less even though fuel is injected, and white smoke is not emitted, replace the exhaust fuel addition injector assembly together with the No. 1 injector holder.



Result:
Proceed to
NEXT



NEXT

11.CHECK INTAKE/EXHAUST SYSTEM
10.CHECK FUEL INJECTION SYSTEM

NEXT

11.CHECK INTAKE/EXHAUST SYSTEM
11.CHECK INTAKE/EXHAUST SYSTEM

NEXT

12.CHECK AFTER TREATMENT CONTROL SYSTEM
12.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

13.REPAIR OR REPLACE MALFUNCTIONING PARTS
13.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P24A200.


a.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL

NOTICE:

Perform the initialization procedure for "Catalyst Deterioration Learning Value Clear" and "DPF Deposition Value Clear".

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION



b.

Replace the exhaust fuel addition injector assembly and No. 1 injector holder.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL

HINT:

If there is no malfunction in the electrical system, Exhaust Temperature B1S2 is 500°C (932°F) or less even though fuel is injected, and white smoke is not emitted, replace the exhaust fuel addition injector assembly together with the No. 1 injector holder.



c.

Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system, intake/exhaust system and after treatment control system.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).



f.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / PM Accumulation Ratio Bank 1 and Exhaust Temperature B1S2 .

Powertrain > Engine and Transmission > Data List
Tester Display
Exhaust Temperature B1S2
PM Accumulation Ratio Bank 1
50003 456 340,90

g.

Check the "Exhaust Temperature B1S2" and "PM Accumulation Ratio Bank 1" until the PM forced regeneration is complete.

Result:

When "PM Accumulation Ratio Bank 1" is 90% or less, "Exhaust Temperature B1S2" is 590°C or more.

Afterward, check that PM forced regeneration completes.



Result:
Proceed to
NEXT



NEXT

END