Refer to DTC P208A14.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P204A12 | Reductant Pressure Sensor Circuit High Circuit Short to Battery | An open or short circuit occurs in the pressure sensor circuit for 3 seconds or more (1 trip detection logic). | ·
Open or short in pressure sensor circuit ·
Pressure sensor (urea pump) ·
Urea pump control ECU |
Comes on | DTC stored | SAE Code: P204D |
| P204A14 | Reductant Pressure Sensor Circuit Low Circuit Short to Ground or Open | An open or short circuit occurs in the pressure sensor circuit for 3 seconds or more (1 trip detection logic). | ·
Open or short in pressure sensor circuit ·
Pressure sensor (urea pump) ·
Urea pump control ECU |
Comes on | DTC stored | SAE Code: P204C |
| DTC No. | Data List |
|---|---|
| P204A12
P204A14 |
Reductant Pressure |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P204A12
P204A14 |
Ignition switch to ON for 3 seconds |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Pressure.
| Tester Display |
|---|
| Reductant Pressure |
Read the Data List according to the display on the GTS.
| Result | Proceed to |
|---|---|
| -50 kPa | A |
| 900 kPa | B |
A
B
| *a | Front view of wire harness connector
(to Urea Pump) |
Disconnect the urea pump connector.
Connect terminals 5 (VPSE) and 4 (PSE) of the pressure sensor (urea pump) wire harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Pressure.
| Tester Display |
|---|
| Reductant Pressure |
Read the Data List according to the display on the GTS.
900 kPa
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the urea pump.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and wait for 3 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the urea pump connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X4-5 (VPSE) - N37-57 (VCPU) | Always | Below 1 Ω |
| X4-4 (PSE) - N37-56 (PU) | Always | Below 1 Ω |
| X4-3 (EPSE) - N37-55 (EPU) | Always | Below 1 Ω |
| X4-5 (VPSE) or N37-57 (VCPU) - Body ground and other terminals | Always | 10 kΩ or higher |
| X4-4 (PSE) or N37-56 (PU) - Body ground and other terminals | Always | 10 kΩ or higher |
| X4-3 (EPSE) or N37-55 (EPU) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the urea pump control ECU.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the urea pump connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Pressure.
| Tester Display |
|---|
| Reductant Pressure |
Read the Data List according to the display on the GTS.
-50 kPa
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the urea pump connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X4-5 (VPSE) - N37-57 (VCPU) | Always | Below 1 Ω |
| X4-4 (PSE) - N37-56 (PU) | Always | Below 1 Ω |
| X4-3 (EPSE) - N37-55 (EPU) | Always | Below 1 Ω |
| X4-5 (VPSE) or N37-57 (VCPU) - Body ground and other terminals | Always | 10 kΩ or higher |
| X4-4 (PSE) or N37-56 (PU) - Body ground and other terminals | Always | 10 kΩ or higher |
| X4-3 (EPSE) or N37-55 (EPU) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG