Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P20CB12  Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Battery  P20CB14  Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P200C4B

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P200C4B

HINT:
·

For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>SYSTEM DESCRIPTION

·

If DTC P20CB12 or P20CB14 is present, refer to the DTC table for Diesel Particulate Filter System.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>SYSTEM DESCRIPTION



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P20CB12 Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Battery Short in exhaust fuel addition injector assembly circuit for 3 seconds (1 trip detection logic).
·

Short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on DTC stored SAE Code: P20CE
P20CB14 Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Ground or Open Open or short in exhaust fuel addition injector assembly circuit for 3 seconds (1 trip detection logic).
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on DTC stored SAE Code: P20CD

Related Data List
DTC No. Data List
P20CB12
P20CB14
·

Fuel Injection Valve + Output Signal Bank 1

·

Fuel Injection Valve - Output Signal Bank 1



HINT:

DTC P200C4B, P200E4B, P20CF00 and/or P24284B will be present if there is an open malfunction in the exhaust fuel addition injector assembly circuit.


MONITOR DESCRIPTION

The ECM monitors the FIV+ terminal (Fuel Injection Valve + Output Signal Bank 1) and FIV- terminal (Fuel Injection Valve - Output Signal Bank 1) of the fuel addition injector assembly.

When a malfunction is detected in the monitor signal while the fuel addition injector assembly is operating or not operating, P20CB12 or P20CB14 is stored.

Normal Condition
Fuel Addition Injector Assembly Operation Status FIV+ Terminal FIV- Terminal
(Fuel Injection Valve + Output Signal Bank 1) (Fuel Injection Valve - Output Signal Bank 1)
Not operating ON OFF
Operating ON ON

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CB12
P20CB14
PM forced regeneration

WIRING DIAGRAM

A445677E01
0.719,1.854 1.177,2.052 0.458,0.198 10 false E78 0.708,2.052 3.573,2.302 2.865,0.25 10 false Exhaust Fuel Addition Injector Assembly 1.76,0.531 2.219,0.729 0.458,0.198 10 false +B 1.729,1.198 2.188,1.396 0.458,0.198 10 false FIV 5.677,0.646 6.313,0.844 0.635,0.198 10 false FIV+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false FIV- 5.344,1.292 5.802,1.49 0.458,0.198 10 false E7 6.052,1.896 6.51,2.094 0.458,0.198 10 false ECM 2.083,0.531 2.542,0.729 0.458,0.198 10 false 2 2.094,1.188 2.552,1.385 0.458,0.198 10 false 1 5.365,0.427 5.823,0.625 0.458,0.198 10 false 1 5.375,1.063 5.833,1.26 0.458,0.198 10 false 3 5.323,0.635 5.781,0.833 0.458,0.198 10 false E8

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E78-2 (+B) - E8-1 (FIV+) Always Below 1 Ω
E78-1 (FIV) - E7-3 (FIV-) Always Below 1 Ω
E78-2 (+B) or E8-1 (FIV+) - Body ground and other terminals Always 10 kΩ or higher
E78-1 (FIV) or E7-3 (FIV-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.



h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END