2007-2013 Highlander Kluger · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION


with Smart Entry and Start System
The cranking holding control system keeps energizing the starter relay after the ECM detects the starter signal (STSW signal) from the main body ECU until the ECM performs a judgment of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the park/neutral position switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the starter relay operating conditions based on the STA terminal voltage status.
A103821E34

without Smart Entry and Start System
While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic):
  1. (a) Vehicle speed more than 20 km/h (12.4 mph)
  2. (b) Engine speed more than 1000 rpm
  3. (c) STA signal ON
  1. Park/neutral position switch
  2. Starter relay circuit
  3. Ignition switch*1
  4. Cranking holding function circuit*2
  5. ECM
  1. *1: Only for vehicles w/o Smart Entry and Start System.
  2. *2: Only for vehicles w/ Smart Entry and Start System.

WIRING DIAGRAM

A172775E14
A243399E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect to the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the tester when the vehicle is driven at 20 km/h (12 mph) or more.

    Result:
    Condition
    Starter Signal
    Result
    Driving at 20 km/h (12 mph) or more
    Close (Starter signal off)
    A
    Open (Starter signal on)
    B



B
Go to step 2
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click herefor U151E, Click here for U151F).

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


3. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Replace the park/neutral position switch assembly (Click herefor U151E, Click here for U151F).


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Idle the engine for 5 seconds or more.

  1. Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC P0617 is output
    B



B
Go to step 5
A

END

5. REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
  1. Repair or replace harness or connector (STA signal circuit).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Idle the engine for 5 seconds or more.

  1. Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC P0617 is output
    B



B
REPLACE ECM (Click here)
A

END


← P0617 Starter Relay Circuit High (Aug 2008 – Jun 2010)P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (May 2007 – Jul 2008) →