2007-2013 Highlander Kluger · Service Manual ENGINE

P0365 Camshaft Position Sensor "B" Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built May 2007 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013

DESCRIPTION

The VVT sensor (G signal) consists of a magnet and MRE element.
The exhaust camshaft has 3 teeth on its inner circumference. When the camshaft gear rotates, the air gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field, resulting in a change in the resistance of the MRE element. The crankshaft angle sensor plate has 34 teeth and outputs 34 signals every engine revolution. The ECM detects the standard crankshaft angle based on the G signal, actual crankshaft angle and engine speed by an NE signal.
DTC No.
DTC Detection Condition
Trouble Area
P0365
P0390
STA ON:
No VVT sensor signal to ECM while cranking for 4 seconds or more
STA OFF:
No VVT sensor signal to ECM with engine speed of 600 rpm or more (1 trip detection logic)
  1. Open or short in VVT sensor for exhaust camshaft circuit
  2. VVT sensor for exhaust camshaft
  3. Exhaust camshaft
  4. ECM
P0367
P0368
P0392
P0393
No VVT sensor signal to ECM with engine speed of 600 rpm or more for 5 seconds or more. (1 trip detection logic)
  1. Open or short in VVT sensor for exhaust camshaft circuit
  2. VVT sensor for exhaust camshaft
  3. Exhaust camshaft
  4. Jumped teeth of timing chain
  5. ECM

WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. CHECK VVT SENSOR FOR EXHAUST CAMSHAFT (SENSOR POWER SOURCE)

  1. A168210E06
    Disconnect the exhaust camshaft VVT sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - Body ground
    Ignition switch on (IG)
    4.5 to 5.0 V



NG
Go to step 7
OK


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST CAMSHAFT - ECM)

  1. A140716E07
    Disconnect the exhaust camshaft VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B42-1 (VVT sensor) - B3-25 (EV1+)
    Always
    Below 1 Ω
    B42-2 (VVT sensor) - B3-24 (EV1-)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B41-1 (VVT sensor) - B3-23 (EV2+)
    Always
    Below 1 Ω
    B41-2 (VVT sensor) - B3-22 (EV2-)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B42-1 (VVT sensor) - B3-25 (EV1+) - Body ground
    Always
    10 kΩ or higher
    B42-2 (VVT sensor) - B3-24 (EV1-) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B41-1 (VVT sensor) - B3-23 (EV2+) - Body ground
    Always
    10 kΩ or higher
    B41-2 (VVT sensor) - B3-22 (EV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)

  1. BR03795E18
    Check the VVT sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE VVT SENSOR
OK


4. CHECK EXHAUST CAMSHAFT
  1. Remove the cylinder head cover.

  1. Check the teeth of the signal plate.



NG
REPLACE EXHAUST CAMSHAFT
OK


5. REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT)
  1. Replace the VVT sensor (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code / Pending.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0365, P0352, P0353, P0354, P0355 or P0356
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END

7. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

  1. A168231E03
    Disconnect the exhaust camshaft VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B42-3 (VC2) - B1-23 (VC)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B41-3 (VC2) - B1-23 (VC)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B42-3 (VC2) or B1-23 (VC) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B41-3 (VC2) or B1-23 (VC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR - ECM)
OK

REPLACE ECM (Click here)


← P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (from Jul 2010)P0365 Camshaft Position Sensor "B" Circuit (Bank 1) (+ 5 more codes) (Jul 2010 – Jul 2013) →