C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Also covers:
- C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
DTCs C1271 to C1276 will be deleted when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs from C1271 to C1276 are output only in Test Mode.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1271 C1272 |
Detected only during Test Mode. |
|
| C1275 C1276 |
Detected only during Test Mode. |
Speed sensor rotor |
- HINT:
- DTCs C1271 and C1275 are for the front speed sensor RH.
- DTCs C1272 and C1276 are for the front speed sensor LH.
- DTCs C1271 and C1275 are for the front speed sensor RH.
WIRING DIAGRAM
Refer to DTCs C1401 and C1402 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Speed Open
FR speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
FL Speed Open
FL speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
- Result:
Result
Proceed to
There are momentary interruptions
A
There are no momentary interruptions
B
There is a constant open circuit
C
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
|
|
||||
| A | |
| 2. REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and the front speed sensor (Click here).
Check that there are no momentary interruptions.
| NEXT | |
| 3. PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 4. READ VALUE ON INTELLIGENT TESTER (FRONT SPEED SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
FL Wheel Speed
FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
| Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
| FR Wheel Direction |
FR wheel direction / FORWARD or BACK |
FORWARD: Forward BACK: Back |
- |
| FL Wheel Direction |
FL wheel direction / FORWARD or BACK |
FORWARD: Forward BACK: Back |
- |
Check that the sensor signal conforms to the wheel direction.
- OK:
- The wheel direction is displayed.
|
|
||||
| OK | |
| 5. PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 6. CHECK FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.

Check the speed sensor installation.
- OK:
- There is no clearance between the sensor and the front steering knuckle.
- The installation nut is tightened properly.
- Torque:
- 8.0 N*m (82 kgf*cm, 71 in.*lbf)
|
|
||||
| OK | |
| 7. CHECK FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
|
|
||||
| OK | |
| 8. CHECK FRONT SPEED SENSOR ROTOR |
Remove the front speed sensor rotor (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
- HINT:
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
|
|
||||
| OK | |
| 9. INSPECT FRONT SPEED SENSOR |
Install the front speed sensor and the front speed sensor rotor.

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for RH:
Tester Connection
Condition
Specified Condition
2 (FR+) - Body ground
Always
10 kΩ or higher
1 (FR-) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
2 (FL+) - Body ground
Always
10 kΩ or higher
1 (FL-) - Body ground
Always
10 kΩ or higher
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.

Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for RH:
Tester Connection
Condition
Specified Condition
A24-7 (FR+) - A25-2 (FR+)
Always
Below 1 Ω
A24-7 (FR+) - Body ground
Always
10 kΩ or higher
A24-6 (FR-) - A25-1 (FR-)
Always
Below 1 Ω
A24-6 (FR-) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
A24-19 (FL+) - A14-2 (FL+)
Always
Below 1 Ω
A24-19 (FL+) - Body ground
Always
10 kΩ or higher
A24-18 (FL-) - A14-1 (FL-)
Always
Below 1 Ω
A24-18 (FL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 11. INSPECT SKID CONTROL ECU (SENSOR INPUT) |
Reconnect the skid control ECU connector.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- for RH:
Tester Connection
Switch Condition
Specified Condition
A25-2 (FR+) - Body ground
Ignition switch on (IG)
8 to 14 V
- for LH:
Tester Connection
Switch Condition
Specified Condition
A14-2 (FL+) - Body ground
Ignition switch on (IG)
8 to 14 V
|
|
||||
| OK | |
| 12. PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 13. REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 14. PERFORM TEST MODE (SIGNAL CHECK) |
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 15. REPLACE FRONT SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the front drive shaft assembly (front speed sensor rotor) (Click here).
- HINT:
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 16. PERFORM TEST MODE (SIGNAL CHECK) |
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
