C1337 Diameter of the Tire is not Uniform
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The skid control ECU measures the speed of each wheel by receiving signals from the speed sensor.These signals are used for recognizing that all 4 wheels are operating properly.
Therefore, all wheel signals must be equal.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1337 |
The following occurs in 3 consecutive trips: At a vehicle speed of 20 km/h (12 mph) or more, there is a 20 % difference or greater in the average speed between the front wheels and rear wheels for 20 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
| 1. CHECK TIRES |
Check the size and condition of all 4 wheels (Click here).
- HINT:
- The DTC is output when tire deformation or a difference in tire size is detected.
- OK:
- The diameter of all 4 tires and air pressure are the same.
- Result:
Result
Proceed to
OK (Except for rear 2WD)
A
OK (for rear 2WD)
B
NG
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK EACH SPEED SENSOR TIP |
Remove the front speed sensor or the rear speed sensor (Click here for front, or Click here for rear).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
|
|
||||
| OK | |
| 3. CHECK EACH SPEED SENSOR ROTOR |
Remove the front speed sensor rotor or the rear speed sensor rotor (Click here for front, or Click here for rear).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
- HINT:
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
|
|
||||
| OK | |
| 4. INSPECT EACH SPEED SENSOR |
Install the speed sensor and the speed sensor rotor.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect each speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for 2WD RH:
Tester Connection
Condition
Specified Condition
2 (FR+) - Body ground
Always
10 kΩ or higher
1 (FR-) - Body ground
Always
10 kΩ or higher
2 (RR+) - Body ground
Always
10 kΩ or higher
1 (RR-) - Body ground
Always
10 kΩ or higher
- for 4WD RH:
Tester Connection
Condition
Specified Condition
2 (FR+) - Body ground
Always
10 kΩ or higher
1 (FR-) - Body ground
Always
10 kΩ or higher
1 (RR+) - Body ground
Always
10 kΩ or higher
2 (RR-) - Body ground
Always
10 kΩ or higher
- for 2WD LH:
Tester Connection
Condition
Specified Condition
2 (FL+) - Body ground
Always
10 kΩ or higher
1 (FL-) - Body ground
Always
10 kΩ or higher
2 (RL+) - Body ground
Always
10 kΩ or higher
1 (RL-) - Body ground
Always
10 kΩ or higher
- for 4WD LH:
Tester Connection
Condition
Specified Condition
2 (FL+) - Body ground
Always
10 kΩ or higher
1 (FL-) - Body ground
Always
10 kΩ or higher
1 (RL+) - Body ground
Always
10 kΩ or higher
2 (RL-) - Body ground
Always
10 kΩ or higher
- Result:
Result
Proceed to
OK (for rear 2WD)
A
OK (Except for rear 2WD)
B
NG
C
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
|
|
||||
| A | |
| 5. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.

Disconnect the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for RH:
Tester Connection
Condition
Specified Condition
z10 ("A"-2) - z10 ("B"-1)
Always
Below 1 Ω
z10 ("A"-2) - z10 ("B"-2)
Always
10 kΩ or higher
z10 ("A"-2) - Body ground
Always
10 kΩ or higher
z10 ("A"-1) - z10 ("B"-2)
Always
Below 1 Ω
z10 ("A"-1) - z10 ("B"-1)
Always
10 kΩ or higher
z10 ("A"-1) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
z9 ("A"-2) - z9 ("B"-1)
Always
Below 1 Ω
z9 ("A"-2) - z9 ("B"-2)
Always
10 kΩ or higher
z9 ("A"-2) - Body ground
Always
10 kΩ or higher
z9 ("A"-1) - z9 ("B"-2)
Always
Below 1 Ω
z9 ("A"-1) - z9 ("B"-1)
Always
10 kΩ or higher
z9 ("A"-1) - Body ground
Always
10 kΩ or higher
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - EACH SPEED SENSOR) |
Reconnect the skid control sensor wire (for 2WD).

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for 2WD RH:
Tester Connection
Condition
Specified Condition
A24-7 (FR+) - A25-2 (FR+)
Always
Below 1 Ω
A24-7 (FR+) - Body ground
Always
10 kΩ or higher
A24-6 (FR-) - A25-1 (FR-)
Always
Below 1 Ω
A24-6 (FR-) - Body ground
Always
10 kΩ or higher
A24-17 (RR+) - z10-2 (RR+)
Always
Below 1 Ω
A24-17 (RR+) - Body ground
Always
10 kΩ or higher
A24-16 (RR-) - z10-1 (RR-)
Always
Below 1 Ω
A24-16 (RR-) - Body ground
Always
10 kΩ or higher
- for 4WD RH:
Tester Connection
Condition
Specified Condition
A24-7 (FR+) - A25-2 (FR+)
Always
Below 1 Ω
A24-7 (FR+) - Body ground
Always
10 kΩ or higher
A24-6 (FR-) - A25-1 (FR-)
Always
Below 1 Ω
A24-6 (FR-) - Body ground
Always
10 kΩ or higher
A24-17 (RR+) - N22-1 (RR+)
Always
Below 1 Ω
A24-17 (RR+) - Body ground
Always
10 kΩ or higher
A24-16 (RR-) - N22-2 (RR-)
Always
Below 1 Ω
A24-16 (RR-) - Body ground
Always
10 kΩ or higher
- for 2WD LH:
Tester Connection
Condition
Specified Condition
A24-19 (FL+) - A14-2 (FL+)
Always
Below 1 Ω
A24-19 (FL+) - Body ground
Always
10 kΩ or higher
A24-18 (FL-) - A14-1 (FL-)
Always
Below 1 Ω
A24-18 (FL-) - Body ground
Always
10 kΩ or higher
A24-5 (RL+) - z9-2 (RL+)
Always
Below 1 Ω
A24-5 (RL+) - Body ground
Always
10 kΩ or higher
A24-4 (RL-) - z9-1 (RL-)
Always
Below 1 Ω
A24-4 (RL-) - Body ground
Always
10 kΩ or higher
- for 4WD LH:
Tester Connection
Condition
Specified Condition
A24-19 (FL+) - A14-2 (FL+)
Always
Below 1 Ω
A24-19 (FL+) - Body ground
Always
10 kΩ or higher
A24-18 (FL-) - A14-1 (FL-)
Always
Below 1 Ω
A24-18 (FL-) - Body ground
Always
10 kΩ or higher
A24-5 (RL+) - O40-1 (RL+)
Always
Below 1 Ω
A24-5 (RL+) - Body ground
Always
10 kΩ or higher
A24-4 (RL-) - O40-2 (RL-)
Always
Below 1 Ω
A24-4 (RL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT SKID CONTROL ECU (SENSOR INPUT) |
Reconnect the skid control ECU connector.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- for 2WD RH:
Tester Connection
Switch Condition
Specified Condition
A25-2 (FR+) - Body ground
Ignition switch on (IG)
8 to 14 V
z10-2 (RR+) - Body ground
Ignition switch on (IG)
8 to 14 V
- for 4WD RH:
Tester Connection
Switch Condition
Specified Condition
A25-2 (FR+) - Body ground
Ignition switch on (IG)
8 to 14 V
N22-1 (RR+) - Body ground
Ignition switch on (IG)
8 to 14 V
- for 2WD LH:
Tester Connection
Switch Condition
Specified Condition
A14-2 (FL+) - Body ground
Ignition switch on (IG)
8 to 14 V
z9-2 (RL+) - Body ground
Ignition switch on (IG)
8 to 14 V
- for 4WD LH:
Tester Connection
Switch Condition
Specified Condition
A14-2 (FL+) - Body ground
Ignition switch on (IG)
8 to 14 V
O40-1 (RL+) - Body ground
Ignition switch on (IG)
8 to 14 V
|
|
||||
| OK | |
| 8. RECONFIRM DTC |
Turn the ignition switch off.
Reconnect the speed sensor connectors.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC (C1337) is output (Except for rear 2WD)
A
DTC (C1337) is output (for rear 2WD)
B
DTC (C1337) is not output
C
|
|
||||
|
|
||||
| A | |
| 9. REPLACE EACH SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor or the rear speed sensor (Click here for front, or Click here for rear).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 10. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC (C1337) is output
A
DTC (C1337) is not output
B
|
|
||||
| A | |
| 11. REPLACE EACH SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the front drive shaft assembly (front speed sensor rotor) or rear drive shaft assembly (rear speed sensor rotor) (Click here for front, or Click here for rear).
- HINT:
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 12. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC (C1337) is output
A
DTC (C1337) is not output
B
|
|
||||
| A | ||
| ||
| 13. REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
Replace the rear axle hub and bearing assembly (rear speed sensor rotor) (Click here).
- HINT:
- The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 14. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC (C1337) is output
A
DTC (C1337) is not output
B
|
|
||||
| A | ||
| ||
