2007-2013 Highlander Kluger · Service Manual BRAKE

C1337 Diameter of the Tire is not Uniform

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The skid control ECU measures the speed of each wheel by receiving signals from the speed sensor.
These signals are used for recognizing that all 4 wheels are operating properly.
Therefore, all wheel signals must be equal.
DTC Code
DTC Detection Condition
Trouble Area
C1337
The following occurs in 3 consecutive trips:
At a vehicle speed of 20 km/h (12 mph) or more, there is a 20 % difference or greater in the average speed between the front wheels and rear wheels for 20 seconds or more.
  1. Tire and wheel size
  2. Tire deformation
  3. Speed sensor rotor
  4. Speed sensor
  5. Speed sensor circuit
  6. Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM

C172250E01

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK TIRES
  1. Check the size and condition of all 4 wheels (Click here).

    HINT:
    The DTC is output when tire deformation or a difference in tire size is detected.

    OK:
    The diameter of all 4 tires and air pressure are the same.


    Result:
    Result
    Proceed to
    OK (Except for rear 2WD)
    A
    OK (for rear 2WD)
    B
    NG
    C



B
Go to step 4

C
REPLACE TIRES SO THAT ALL FOUR TIRES ARE SAME SIZE
A


2. CHECK EACH SPEED SENSOR TIP
  1. Remove the front speed sensor or the rear speed sensor (Click here for front, or Click here for rear).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE EACH SPEED SENSOR
OK


3. CHECK EACH SPEED SENSOR ROTOR
  1. Remove the front speed sensor rotor or the rear speed sensor rotor (Click here for front, or Click here for rear).

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

    HINT:
    1. If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
    2. If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.



NG
CLEAN OR REPLACE EACH SPEED SENSOR ROTOR
OK


4. INSPECT EACH SPEED SENSOR

  1. C180257E02
    Install the speed sensor and the speed sensor rotor.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect each speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for 2WD RH:
    Tester Connection
    Condition
    Specified Condition
    2 (FR+) - Body ground
    Always
    10 kΩ or higher
    1 (FR-) - Body ground
    Always
    10 kΩ or higher
    2 (RR+) - Body ground
    Always
    10 kΩ or higher
    1 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 4WD RH:
    Tester Connection
    Condition
    Specified Condition
    2 (FR+) - Body ground
    Always
    10 kΩ or higher
    1 (FR-) - Body ground
    Always
    10 kΩ or higher
    1 (RR+) - Body ground
    Always
    10 kΩ or higher
    2 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 2WD LH:
    Tester Connection
    Condition
    Specified Condition
    2 (FL+) - Body ground
    Always
    10 kΩ or higher
    1 (FL-) - Body ground
    Always
    10 kΩ or higher
    2 (RL+) - Body ground
    Always
    10 kΩ or higher
    1 (RL-) - Body ground
    Always
    10 kΩ or higher
    for 4WD LH:
    Tester Connection
    Condition
    Specified Condition
    2 (FL+) - Body ground
    Always
    10 kΩ or higher
    1 (FL-) - Body ground
    Always
    10 kΩ or higher
    1 (RL+) - Body ground
    Always
    10 kΩ or higher
    2 (RL-) - Body ground
    Always
    10 kΩ or higher


    Result:
    Result
    Proceed to
    OK (for rear 2WD)
    A
    OK (Except for rear 2WD)
    B
    NG
    C

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



B
Go to step 6

C
REPLACE EACH SPEED SENSOR
A


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

  1. C169030E02
    Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control sensor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    z10 ("A"-2) - z10 ("B"-1)
    Always
    Below 1 Ω
    z10 ("A"-2) - z10 ("B"-2)
    Always
    10 kΩ or higher
    z10 ("A"-2) - Body ground
    Always
    10 kΩ or higher
    z10 ("A"-1) - z10 ("B"-2)
    Always
    Below 1 Ω
    z10 ("A"-1) - z10 ("B"-1)
    Always
    10 kΩ or higher
    z10 ("A"-1) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    z9 ("A"-2) - z9 ("B"-1)
    Always
    Below 1 Ω
    z9 ("A"-2) - z9 ("B"-2)
    Always
    10 kΩ or higher
    z9 ("A"-2) - Body ground
    Always
    10 kΩ or higher
    z9 ("A"-1) - z9 ("B"-2)
    Always
    Below 1 Ω
    z9 ("A"-1) - z9 ("B"-1)
    Always
    10 kΩ or higher
    z9 ("A"-1) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - EACH SPEED SENSOR)

  1. C169131E03
    Reconnect the skid control sensor wire (for 2WD).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for 2WD RH:
    Tester Connection
    Condition
    Specified Condition
    A24-7 (FR+) - A25-2 (FR+)
    Always
    Below 1 Ω
    A24-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    A24-6 (FR-) - A25-1 (FR-)
    Always
    Below 1 Ω
    A24-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    A24-17 (RR+) - z10-2 (RR+)
    Always
    Below 1 Ω
    A24-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A24-16 (RR-) - z10-1 (RR-)
    Always
    Below 1 Ω
    A24-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 4WD RH:
    Tester Connection
    Condition
    Specified Condition
    A24-7 (FR+) - A25-2 (FR+)
    Always
    Below 1 Ω
    A24-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    A24-6 (FR-) - A25-1 (FR-)
    Always
    Below 1 Ω
    A24-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    A24-17 (RR+) - N22-1 (RR+)
    Always
    Below 1 Ω
    A24-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A24-16 (RR-) - N22-2 (RR-)
    Always
    Below 1 Ω
    A24-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 2WD LH:
    Tester Connection
    Condition
    Specified Condition
    A24-19 (FL+) - A14-2 (FL+)
    Always
    Below 1 Ω
    A24-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    A24-18 (FL-) - A14-1 (FL-)
    Always
    Below 1 Ω
    A24-18 (FL-) - Body ground
    Always
    10 kΩ or higher
    A24-5 (RL+) - z9-2 (RL+)
    Always
    Below 1 Ω
    A24-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A24-4 (RL-) - z9-1 (RL-)
    Always
    Below 1 Ω
    A24-4 (RL-) - Body ground
    Always
    10 kΩ or higher
    for 4WD LH:
    Tester Connection
    Condition
    Specified Condition
    A24-19 (FL+) - A14-2 (FL+)
    Always
    Below 1 Ω
    A24-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    A24-18 (FL-) - A14-1 (FL-)
    Always
    Below 1 Ω
    A24-18 (FL-) - Body ground
    Always
    10 kΩ or higher
    A24-5 (RL+) - O40-1 (RL+)
    Always
    Below 1 Ω
    A24-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A24-4 (RL-) - O40-2 (RL-)
    Always
    Below 1 Ω
    A24-4 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT SKID CONTROL ECU (SENSOR INPUT)

  1. C169132E03
    Reconnect the skid control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for 2WD RH:
    Tester Connection
    Switch Condition
    Specified Condition
    A25-2 (FR+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    z10-2 (RR+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 4WD RH:
    Tester Connection
    Switch Condition
    Specified Condition
    A25-2 (FR+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    N22-1 (RR+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 2WD LH:
    Tester Connection
    Switch Condition
    Specified Condition
    A14-2 (FL+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    z9-2 (RL+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 4WD LH:
    Tester Connection
    Switch Condition
    Specified Condition
    A14-2 (FL+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    O40-1 (RL+) - Body ground
    Ignition switch on (IG)
    8 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


8. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Reconnect the speed sensor connectors.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC (C1337) is output (Except for rear 2WD)
    A
    DTC (C1337) is output (for rear 2WD)
    B
    DTC (C1337) is not output
    C



B
Go to step 13

C
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


9. REPLACE EACH SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor or the rear speed sensor (Click here for front, or Click here for rear).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


10. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC (C1337) is output
    A
    DTC (C1337) is not output
    B



B
END
A


11. REPLACE EACH SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the front drive shaft assembly (front speed sensor rotor) or rear drive shaft assembly (rear speed sensor rotor) (Click here for front, or Click here for rear).

    HINT:
    1. If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
    2. If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


12. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC (C1337) is output
    A
    DTC (C1337) is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

13. REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor (Click here).

  1. Replace the rear axle hub and bearing assembly (rear speed sensor rotor) (Click here).

    HINT:
    The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


14. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC (C1337) is output
    A
    DTC (C1337) is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← C1337 Diameter of the Tire is not Uniform (May 2007 – Jul 2008)C1337 Diameter of the Tire is not Uniform (from Jul 2010) →