C1426 Stop Light Switch OFF Stuck Malfunction
Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The skid control ECU (housed in the actuator assembly) inputs stop light switch signals and the condition of brake operation.The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1426 |
When the brake pedal load sensing switch is ON, the master cylinder pressure is 2 MPa or more and the deceleration calculated from the vehicle speed is 0.2 G or more, the stop light switch is OFF for 2 seconds or more. |
|
WIRING DIAGRAM
Refer to DTC C1425 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
| 1. CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
- OK:
Condition
Illumination Condition
Brake pedal depressed
ON
Brake pedal released
OFF
|
|
||||
| OK | |
| 2. READ VALUE ON INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Select the Data List mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.
- OK:
- First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.
- Result:
Result
Proceed to
OK
A
NG (Turning on of the stop light switch is not confirmed)
B
NG (The brake pedal load sensing switch turns on first)
C
|
|
||||
|
|
||||
| A | |
| 3. RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC (C1426) is not output
A
DTC (C1426) is output
B
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| A | ||
| ||
| 4. INSPECT STOP FUSE |
Remove the STOP fuse from the main body ECU (instrument panel junction block).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
STOP (10 A) fuse
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL) |
Install the STOP fuse.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the stop light switch connector.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
A20-2 - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 6. INSPECT STOP LIGHT SWITCH |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Switch pin free
Below 1 Ω
1 - 2
Switch pin pushed in
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT STOP LIGHT CONTROL RELAY |
Remove the stop light control relay.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 4
Voltage is not applied between terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ENGINE ROOM RELAY BLOCK) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A20-1 - Stop light control relay terminal 4
Always
Below 1 Ω
A20-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.

Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A24-2 (STP) - Stop light control relay terminal 3
Always
Below 1 Ω
A24-2 (STP) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 10. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click here).
- HINT:
- Reinstall the relay, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Result
Proceed to
DTC (C1426) is not output
A
DTC (C1426) is output
B
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| A | ||
| ||
| 11. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK) |
Turn the ignition switch off.

Remove the stop light control relay.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A24-2 (STP) - Stop light control relay terminal 3
Always
Below 1 Ω
A24-2 (STP) - Body ground
Always
10 kΩ or higher
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| OK | ||
| ||
| 12. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch installation (Click here).
- OK:
- The brake pedal height and stop light switch installation are normal.
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| OK | ||
| ||
