2007-2013 Highlander Kluger · Service Manual BRAKE

C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

DTC C1281 will be deleted when the master cylinder pressure sensor sends a master cylinder pressure signal or when Test Mode ends. DTC C1281 is output only in Test Mode.
DTC Code
DTC Detection Condition
Trouble Area
C1281
Detected only during Test Mode.
  1. Stop light switch
  2. Brake pedal load sensing switch
  3. Master cylinder pressure sensor

WIRING DIAGRAM

Refer to DTCs C1425 and C1429 (Click here, or Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
INSPECT STOP LIGHT CIRCUIT (Click here)
OK


2. READ VALUE ON INTELLIGENT TESTER (STOP LIGHT SWITCH AND BRAKE PEDAL LOAD SENSING SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond the specified point
    OFF: Brake pedal not depressed beyond the specified point
    -

  1. Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.

  1. Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.

    OK:
    First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.


    Result:
    Result
    Proceed to
    OK
    A
    NG (Turning on of the stop light switch is not confirmed)
    B
    NG (Turning on of the brake pedal load sensing switch is not confirmed)
    C
    NG (The brake pedal load sensing switch turns on first)
    D



B
Go to step 5

C
Go to step 6

D
Go to step 7
A


3. READ VALUE ON INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR)
  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Master Cylinder Sensor
    Master cylinder pressure sensor / min.: 0 V, max.: 5 V
    When brake pedal is released: 0.3 to 0.9 V
    Reading increases when brake pedal is depressed

  1. Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the intelligent tester changes when the brake pedal is depressed.

    OK:
    When the pedal is depressed, voltage displayed on the intelligent tester increases.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


4. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

5. INSPECT SKID CONTROL ECU (STP TERMINAL)

  1. C160263E44
    Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-2 (STP) - Body ground
    Stop light switch ON
    (Brake pedal depressed)
    8 to 14 V
    A24-2 (STP) - Body ground
    Stop light switch OFF
    (Brake pedal released)
    Below 1.5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

6. INSPECT SKID CONTROL ECU (FSW+ TERMINAL)

  1. C160263E45
    Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-27 (FSW+) - Body ground
    Brake pedal load sensing switch OFF
    (Brake pedal depressed)
    0.9 to 1.1 kΩ
    A24-27 (FSW+) - Body ground
    Brake pedal load sensing switch ON
    (Brake pedal released)
    192 to 234 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FSW+ CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

7. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch installation (Click here).

    OK:
    The brake pedal height and stop light switch installation are normal.



NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH (Click here)
OK

REPLACE BRAKE PEDAL SUB-ASSEMBLY (BRAKE PEDAL LOAD SENSING SWITCH) (Click here)


← C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) (May 2007 – Jul 2008)C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) (from Jul 2010) →