C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
DTC C1281 will be deleted when the master cylinder pressure sensor sends a master cylinder pressure signal or when Test Mode ends. DTC C1281 is output only in Test Mode.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1281 |
Detected only during Test Mode. |
|
WIRING DIAGRAM
Refer to DTCs C1425 and C1429 (Click here, or Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
| 1. CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
- OK:
Condition
Illumination Condition
Brake pedal depressed
ON
Brake pedal released
OFF
|
|
||||
| OK | |
| 2. READ VALUE ON INTELLIGENT TESTER (STOP LIGHT SWITCH AND BRAKE PEDAL LOAD SENSING SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Select the Data List mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Lamp SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.
- OK:
- First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.
- Result:
Result
Proceed to
OK
A
NG (Turning on of the stop light switch is not confirmed)
B
NG (Turning on of the brake pedal load sensing switch is not confirmed)
C
NG (The brake pedal load sensing switch turns on first)
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. READ VALUE ON INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR) |
Select the Data List mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Master Cylinder Sensor
Master cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
Reading increases when brake pedal is depressed
Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the intelligent tester changes when the brake pedal is depressed.
- OK:
- When the pedal is depressed, voltage displayed on the intelligent tester increases.
|
|
||||
| OK | |
| 4. PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 5. INSPECT SKID CONTROL ECU (STP TERMINAL) |
Turn the ignition switch off.

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
A24-2 (STP) - Body ground
Stop light switch ON
(Brake pedal depressed)
8 to 14 V
A24-2 (STP) - Body ground
Stop light switch OFF
(Brake pedal released)
Below 1.5 V
|
|
||||
| OK | ||
| ||
| 6. INSPECT SKID CONTROL ECU (FSW+ TERMINAL) |
Turn the ignition switch off.

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
A24-27 (FSW+) - Body ground
Brake pedal load sensing switch OFF
(Brake pedal depressed)
0.9 to 1.1 kΩ
A24-27 (FSW+) - Body ground
Brake pedal load sensing switch ON
(Brake pedal released)
192 to 234 Ω
|
|
||||
| OK | ||
| ||
| 7. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch installation (Click here).
- OK:
- The brake pedal height and stop light switch installation are normal.
|
|
||||
| OK | ||
| ||
